Nissan Pathfinder. Manual — part 1056
B210F TRANSMISSION RANGE SWITCH
SEC-87
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector F24 terminal 66 and transmission range switch
harness connector F36 terminal 10.
4. Check continuity between TCM harness connector F15 (A) terminal 20 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> Inspection End.
IPDM E/R
Ground
Condition
Voltage (V)
Connector Terminal
E119
37
Ground
CVT selector
lever
P (Park) or N
(Neutral)
Battery voltage
Other than
above
0
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F36
10
F24
66
Yes
Transmission range switch
Ground
Continuity
Connector
Terminal
F36
10
Ground
No
SEC-88
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 TRANSMISSION RANGE SWITCH
B2110 TRANSMISSION RANGE SWITCH
Description
INFOID:0000000009175992
IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000009175993
DTC DETECTION LOGIC
NOTE:
• If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2110 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P (Park) or N (Neutral) position
-
Do not depress the brake pedal
2. Check “Self-diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009175994
Regarding Wiring Diagram information, refer to
or
1.
CHECK DTC WITH BCM
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector E119 terminal 37 and ground under following condi-
tion.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2110
TRANSMISSION
RANGE SWITCH
IPDM E/R detects mismatch between the signal
below for 1 second or more.
• Transmission range switch input signal
• Harness or connectors
Transmission range switch circuit is
open or shorted
• Transmission range switch
B2110 TRANSMISSION RANGE SWITCH
SEC-89
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector F24 terminal 66 and transmission range switch
harness connector F36 terminal 10.
4. Check continuity between TCM harness connector F15 terminal 20 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-49, "Intermittent Incident"
.
>> Inspection End.
IPDM E/R
Ground
Condition
Voltage (V)
Connector
Terminal
E119
37
Ground
CVT selector lever
P (Park) or N (Neutral)
Battery voltage
Other than above
0
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F36
10
F24
66
Yes
Transmission range switch
Ground
Continuity
Connector
Terminal
F36
10
Ground
No
SEC-90
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2190 NATS ANTENNA AMP.
B2190 NATS ANTENNA AMP.
Description
INFOID:0000000009175995
Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed.
Prohibits starting of the engine when an unregistered ID of Intelligent Key is used.
DTC Logic
INFOID:0000000009175996
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1. Contact Intelligent Key back side to push-button ignition switch.
2. Check DTC in “Self-Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1. Press the push-button ignition switch.
2. Check DTC in “Self-Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009175997
Regarding Wiring Diagram information, refer to
.
1.
CONNECTOR INSPECTION
1. Disconnect BCM and NATS antenna amp.
2. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace as necessary.
2.
CHECK NATS ANTENNA AMP. CIRCUIT
1. Disconnect BCM connector and NATS antenna amp. connector.
2. Check continuity between BCM harness connector and NATS antenna amp. harness connector.
3. Check continuity between BCM harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2190
NATS ANTENNA
AMP
Inactive communication between NATS antenna
amp. and BCM.
• Harness or connectors
(The NATS antenna amp. circuit is
open or shorted)
• NATS antenna amp.
• BCM
BCM
NATS antenna amp.
Continuity
Connector
Terminal
Connector
Terminal
M80
126
M21
3
Yes
127
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст