Nissan Pathfinder. Manual — part 134
AV
NORMAL OPERATING CONDITION
AV-363
< SYMPTOM DIAGNOSIS >
[MID AUDIO WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000009174618
RELATED TO NOISE
The majority of the audio concerns are the result of outside causes (bad CD, electromagnetic interference,
etc.).
The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
• Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the
antenna at a different time from the waves which reflect off mountains or buildings.
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
Type of Noise and Possible Cause
RELATED TO HANDS-FREE PHONE
Occurrence condition
Possible cause
Occurs only when engine is ON.
A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.
• Ignition components
The occurrence of the noise is linked with the operation of the fuel pump.
• Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.
A cracking or snapping sound occurs with the op-
eration of various switches.
• Relay malfunction, AV control unit malfunc-
tion
The noise occurs when various motors are operat-
ing.
• Motor case ground
• Motor
The noise occurs constantly, not just under certain conditions.
• Rear defogger coil malfunction
• Open circuit in printed heater
• Poor ground of antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially when
it is vibrating excessively.
• Ground wire of body parts
• Ground due to improper part installation
• Wiring connections or a short circuit
Symptom
Cause and Counter measure
Does not recognize cellular phone connection (No connection is
displayed on the display at the guide).
Some Bluetooth
®
enabled cellular phones may not be recognized
by the in-vehicle phone module.
Refer to “RELATED TO HANDS-FREE PHONE (Check Compati-
bility)” in
Cannot use hands-free phone.
Customer will not be able to use a hands-free phone under the fol-
lowing conditions:
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio
waves; such as in a tunnel, in an underground parking garage,
near a tall building or in a mountainous area.
• The cellular phone is locked to prevent it from being dialed.
NOTE:
While a cellular phone is connected through the Bluetooth
®
wire-
less connection, the battery power of the cellular phone may dis-
charge quicker than usual. The Bluetooth
®
Hands-Free Phone
System cannot charge cellular phones.
AV-364
< SYMPTOM DIAGNOSIS >
[MID AUDIO WITH BOSE]
NORMAL OPERATING CONDITION
The other party’s voice cannot be heard by hands-free phone.
When the radio wave condition is not ideal or ambient sound is too
loud, it may be difficult to hear the other person’s voice during a
call.
Poor sound quality.
Do not place the cellular phone in an area surrounded by metal or
far away from the in-vehicle phone module to prevent tone quality
degradation and wireless connection disruption.
Symptom
Cause and Counter measure
AV
AV CONTROL UNIT
AV-365
< REMOVAL AND INSTALLATION >
[MID AUDIO WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
AV CONTROL UNIT
Exploded View
INFOID:0000000009763202
Removal and Installation
INFOID:0000000009763201
REMOVAL
CAUTION:
• Remove battery terminal and AV control unit after a lapse of 30 seconds or more after turning the
ignition switch OFF.
• Before replacing AV control unit, perform "READ CONFIGURATION" to save current vehicle specifi-
cation. Refer to
AV-277, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"
.
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
1. Disconnect the negative battery terminal. Refer to
PG-90, "Removal and Installation"
2. Remove cluster lid C. Refer to
IP-22, "CLUSTER LID C : Removal and Installation"
3. Remove the screws, then pull out the AV control unit.
4. Disconnect the harness connectors from the AV control unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
AV control unit bracket (LH)
2.
A/C auto amp.
3.
AV control unit
4.
AV control unit bracket (RH)
ALNIA1436ZZ
AV-366
< REMOVAL AND INSTALLATION >
[MID AUDIO WITH BOSE]
AV CONTROL UNIT
• When replacing AV control unit, perform "WRITE CONFIGURATION". Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст