Almera Tino V10 (2003 year). Manual — part 161
Wiring Diagram — TURN —
NLEL0431
LHD MODELS
NLEL0431S01
YEL940D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN —
EL-65
YEL941D
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-66
RHD MODELS
NLEL0431S02
YEL045E
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-67
YEL571E
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-68
Trouble Diagnoses
NLEL0432
Symptom
Possible cause
Repair order
Turn signal and hazard warning
lamps do not operate.
1. Smart entrance control unit
2. Smart entrance control unit cir-
cuit
1. Check power door lock operation.
2. Check power supply and ground circuit for smart
entrance control unit.
Turn signal lamps do not operate
but hazard warning lamps operate.
1. Turn signal switch
2. Open in turn signal switch cir-
cuit
1. Check turn signal switch.
2. Check turn signal switch ground for open circuit.
Hazard warning lamps do not
operate but turn signal lamps
operate.
1. Hazard switch
2. Open in hazard switch circuit
1. Check hazard switch.
2. Check the following.
I
Harness for open or short between smart entrance
control unit and ground
I
Hazard switch ground for open circuit
Front turn signal lamp LH or RH
does not operate.
1. Bulb
2. Open in front turn signal lamp
circuit
1. Check bulb.
2. Check power supply and ground circuit for front turn
signal lamp.
Side turn signal lamp LH or RH
does not operate.
1. Bulb
2. Open in side turn signal lamp
circuit
1. Check bulb.
2. Check power supply and ground circuit for side turn
signal lamp.
Rear combination lamp LH or RH
does not operate.
1. Bulb
2. Open in rear combination lamp
circuit
1. Check bulb.
2. Check grounds check power supply and ground circuit
for rear combination lamp.
LH and RH turn indicators do not
operate.
1. Ground
1. Check grounds E24, E73, B30 or D89 (LHD models)
2. Perform self-diagnosis for smart entrance control unit
with CONSULT-II.
I
If self-diagnosis result is OK, replace combination
meter.
I
If self-diagnosis result is NG, refer to EL-351, “CAN
Communication Line Check”.
LH or RH turn indicator does not
operate.
1. Bulb
1. Check bulb in combination meter.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
TURN SIGNAL AND HAZARD WARNING LAMPS
Trouble Diagnoses
EL-69
Schematic
NLEL0433
YEL942D
ILLUMINATION
Schematic
EL-70
Wiring Diagram — ILL —
NLEL0434
YEL943D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
ILLUMINATION
Wiring Diagram — ILL —
EL-71
YEL944D
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-72
YEL945D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-73
YEL946D
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-74
YEL947D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-75
YEL948D
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-76
System Description
NLEL0435
POWER SUPPLY AND GROUND
NLEL0435S01
Power is supplied at all times:
I
through 15A fuse [No. 5, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 56,
I
through 10A fuse [No. 13, located in the fuse block (J/B)]
I
to spot lamp terminal 1,
I
to interior room lamp terminal 1 (with sunroof),
I
to interior room lamp terminal 5 (without sunroof), or
I
to rear reading lamp terminal 5 (with rear reading lamp).
I
through 10A fuse [No. 12, located in the fuse block (J/B)]
I
to key switch terminal 1 (for RHD models).
When the key is removed from ignition key cylinder, power is interrupted:
I
through key switch terminal 2
I
to smart entrance control unit terminal 5.
With the ignition key switch in the ON or START position, power is supplied:
I
through 10A fuse [No. 10, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 29.
Ground is supplied:
I
through body grounds terminals M28, M48 and M109 (QG engine models) or F51 (YD engine models).
I
to smart entrance control unit terminal 53
When the driver side door is opened, ground is supplied:
I
through body grounds B24 and B30 or D89 (for LHD models)
I
to door switch driver side terminal 3
I
from door switch driver side terminal 2
I
to smart entrance control unit terminal 43.
When any door is opened, ground is supplied:
I
through case ground of each door switch
I
to each door switch terminal 1
I
to smart entrance control unit terminal 44.
When the driver side door is unlocked by the door lock/unlock switch, the smart entrance control unit receives
a ground signal:
I
through body grounds B24 and B30, or D89 (for LHD models)
I
to power window main switch terminal 3
I
from power window main switch terminal 7
I
to smart entrance control unit terminal 14.
When the driver side door is locked by the door lock/unlock switch, the smart entrance control unit receives
a ground signal:
I
through body grounds B24 and B30, or D89 (for LHD models)
I
to power window main switch terminal 3
I
from power window main switch terminal 14
I
to smart entrance control unit terminal 13.
When a signal, or combination of signals is received by the smart entrance control unit, ground is supplied:
I
through smart entrance control unit terminal 28
I
to interior room lamp terminal 5.
With power and ground supplied, the interior room lamp illuminates when the lamp switch is in “DOOR” posi-
tion.
SWITCH OPERATION
NLEL0435S02
When interior room lamp switch is in “ON” position, ground is supplied:
I
through body grounds M28, M48, M109 (QG engine) or F51 (YD engine)
I
to interior room lamp terminal 3.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INTERIOR ROOM LAMP
System Description
EL-77
When spot lamp (LH or RH) is ON, ground is supplied:
I
through body grounds M28, M48, M109 (QG engine models) or F51 (YD engine models)
I
to spot lamp terminal 2.
When rear reading lamp (LH or RH) is ON, ground is supplied:
I
through body grounds M28, M48, M109 (QG engine models) or F51 (YD engine models)
I
to rear reading lamp terminal 6.
With power and ground supplied, the interior room lamp, spot lamp or rear reading lamp illuminates.
INTERIOR ROOM LAMP TIMER OPERATION
NLEL0435S03
When interior room lamp switch is in the “DOOR” position, the smart entrance control unit keeps the interior
room lamp illuminated for about 30 seconds when:
I
unlock signal is supplied from door lock/unlock switch while all doors are closed
I
unlock signal is supplied from remote controller or door key cylinder while all doors are closed
I
key is removed from ignition key cylinder while all doors are closed (with super lock system)
I
driver’s door is opened and then closed
The timer is canceled when:
I
driver’s door is locked,
I
driver’s door is opened, or
I
ignition switch is turned ON.
ON-OFF CONTROL
NLEL0435S04
When the driver side door, front passenger door, rear LH or RH door is opened, the interior room lamp turns
on while the interior room lamp switch is in the “DOOR” position.
BATTERY SAVER
NLEL0435S11
The interior room lamp is turned OFF automatically with the lamp switch in the “DOOR” position after about
30 minutes, if the lamp remains lit by the door switch open signal.
INTERIOR ROOM LAMP
System Description (Cont’d)
EL-78
Schematic
NLEL0637
YEL949D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INTERIOR ROOM LAMP
Schematic
EL-79
Wiring Diagram — ROOM/L —
NLEL0436
YEL950D
INTERIOR ROOM LAMP
Wiring Diagram — ROOM/L —
EL-80
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст