Qashqai J11. Security control system — part 13
COMPONENT PARTS
SEC-193
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Sensor Cancel Switch
INFOID:0000000010479734
BCM deactivates intruder sensor for the vehicle security system
when BCM receives sensor cancel switch ON signal.
JMKIB3261ZZ
SEC-194
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
SYSTEM
NISSAN ANTI-THEFT SYSTEM
NISSAN ANTI-THEFT SYSTEM : System Description
INFOID:0000000010338033
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
Nissan Anti-Theft System (NATS) has the following immobilizer functions:
• NATS shows high anti-theft performance to prevent engine from starting by anyone other than the owner
who has the registered ignition key.
• The ignition key has NATS ID and only ignition key which has the same ID as the ID registered in BCM and
ECM can start engine. This makes high anti-theft performance to prevent the vehicle from being stolen using
a copied ignition key.
• Security indicator lamp always blinks when ignition switch is in any position other than ON. Therefore, NATS
warns outsiders that the vehicle is equipped with the anti-theft system.
• If the system detects a malfunction, security indicator lamp illuminates when ignition switch is turned ON.
• If the owner requires, ignition key ID can be registered for up to 5 keys.
• During trouble diagnosis, when additional ignition key is needed, or when the following components are
replaced, the ID registration is required.
- BCM
- Ignition key
• Possible symptom of NATS malfunction is “Engine cannot start”. The engine also can not be started
because of other than the NATS malfunction, so start the trouble diagnosis according to
• If ECM other than Genuine NISSAN parts is installed, the engine cannot be started. For ECM replacement
procedure, refer to
ECH-320, "Removal and Installation"
(HRA2DDT engine models),
EC9-409, "Removal and Installation"
(R9M engine models).
SECURITY INDICATOR LAMP
• Security indicator lamp is located on combination meter and warns that the vehicle is equipped with NATS.
• Security indicator lamp always blinks, when the ignition switch is in any position other than ON.
• Security indicator lamp turns OFF when the ignition switch is turned ON.
OPERATION WHEN IGNITION KEY IS INSERTED INTO IGNITION KEY CYLINDER
1.
When ignition switch is turned ON, BCM activates NATS antenna amp. to start NATS ID verification with
the ignition key (transponder is integrated).
2.
BCM receives the NATS ID signal from ignition key via NATS antenna amp. and verifies it with the regis-
tered ID.
3.
When the NATS ID verification result is OK, BCM performs the ID verification between BCM and ECM.
4.
When the verification result is OK, BCM transmits the verification OK signal to ECM, and then ECM can
start the engine.
JMKIB3228GB
SYSTEM
SEC-195
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM
VEHICLE SECURITY SYSTEM : System Description
INFOID:0000000010506849
SYSTEM DIAGRAM
BCM INPUT/OUTPUT SIGNAL CHART
Input Signal Item
Output Signal Item
JMKIB3230GB
Transmit unit
Signal name
IPDM E/R
CAN communication
Hood switch signal
Each door switch
Door switch signal
Siren control unit
Alarm link signal
Sensor cancel switch
Sensor cancel switch signal
Reception unit
Signal name
Combination meter (security indicator lamp)
Security indicator lamp signal
Siren control unit
Alarm link signal
Hazard warning lamp
Hazard warning lamp signal
SEC-196
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
SYSTEM DESCRIPTION
• The system reduces the possibility of a theft or mischief by sounding siren and blinking hazard warning lamp
continuously. The system activates siren and hazard warning lamp when detecting that the door or hood is
opened, or there is an illegal attempt to enter into the passenger room, while the system is in the ARMED
phase.
• Security indicator lamp on combination meter always blinks when ignition switch is any position other than
ON to warn that the vehicle is equipped with a VEHICLE SECURITY SYSTEM.
• Anti-theft function is improved by the adoption of intruder sensor that detects an attempt to enter into the
passenger room.
• Activation or deactivation of intruder sensor can be selected by sensor cancel switch.
• Siren control unit equips a built-in battery. Replace siren control unit once every 10 years because the war-
ranty for built-in battery expires after 10 years.
• Each time the system switches to the ARMED phase from the PRE-ARMED phase, the self-diagnosis is per-
formed by the siren control unit and each sensor. If any malfunction is detected, the siren sounds* 5 times to
inform the driver that a malfunction is detected and the vehicle security system does not function properly.
Malfunctioning part can be checked by “SIREN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using
CONSULT. Refer to
SEC-207, "Diagnosis Description"
.
*: Siren sounds for 0.2 seconds and sound interval is 0.4 seconds.
Operation Flow
JMKIB1929GB
No.
System state
Switching condition
DISARMED to
FULL PRE-
ARMED
When all conditions of A and
one condition of B is satis-
fied.
A
B
• Ignition switch: OFF
• All doors: Closed
• Hood: Closed
All doors are locked by:
• LOCK button of Key fob
• Door lock and unlock switch
DISARMED to
PARTIAL PRE-
ARMED
When all conditions of A and
one condition of B is satis-
fied.
A
B
• Ignition switch: OFF
• Hood or any door: Open
All doors are locked by:
• LOCK button of Key fob
• Door lock and unlock switch
FULL PRE-
ARMED to DIS-
ARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Key fob: ON
• Door lock and unlock switch: ON
PARTIAL PRE-
ARMED to DIS-
ARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Key fob: ON
• Door lock and unlock switch: ON
SYSTEM
SEC-197
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NOTE:
• To lock/unlock all doors by operating remote controller button of Key fob for details, refer to
Disarmed Phase
VEHICLE SECURITY SYSTEM switches to the DISARMED phase while any doors or hood is open because it
is assumed that the owner is in or nearby the vehicle.
Pre-armed Phase
• VEHICLE SECURITY SYSTEM switches to the PRE-ARMED phase and blinks security indicator lamp
quickly for approximately 20 seconds when all doors are locked by Key fob, while all doors and hood are
closed.
• VEHICLE SECURITY SYSTEM that is in the PRE-ARMED phase switches to the DISARMED phase when
all doors are unlocked by Key fob.
• VEHICLE SECURITY SYSTEM does not activate siren when door or hood is open while VEHICLE SECU-
RITY SYSTEM is in the PRE-ARMED phase. When the door or hood is closed again, VEHICLE SECURITY
SYSTEM stays in the PRE-ARMED phase.
PARTIAL PRE-
ARMED to FULL
PRE-ARMED
When all of the following
conditions are satisfied.
• All doors: Closed
• Hood: Closed
FULL PRE-
ARMED to PAR-
TIAL PRE-ARMED
When one of the following
condition is satisfied.
• Any door: Opened
• Hood: Opened
FULL PRE-
ARMED to FULL
ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
• All doors: Locked
• Hood: Closed
PARTIAL PRE-
ARMED to PAR-
TIAL ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
PARTIAL to FULL
ARMED
When all of the following
conditions are satisfied for
20 seconds.
• Ignition switch: OFF
• All doors: Closed
• Hood: Closed
FULL ARMED to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Key fob: ON
• Door lock and unlock switch: ON
PARTIAL ARMED
to DISARM
FULL ARMED to
ALARM
When one of the following
condition is detected.
• Any door or hood is opened
• Battery is connect and disconnect
• Movement to enter into passenger room
• Communication between BCM and siren control unit is interrupted
• Communication between siren control unit and intruder sensor is in-
terrupted
PARTIAL ARMED
to ALARM
When one of the following
condition is detected.
• Any door or hood is opened
• Battery is connect and disconnect
• Communication between BCM and siren control unit is interrupted
• Communication between siren control unit and intruder sensor is in-
terrupted
ALARM to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Key fob: ON
• Door lock and unlock switch: ON
ALARM to ALARM
PAUSE
27.5 seconds are passed.
ARM PAUSE to
FULL ARMED
5 seconds are passed after deactivating ALARM.
ARM PAUSE to
PARTIAL ARMED
ALARM PAUSE to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ON
• UNLOCK button of Key fob: ON
• Door lock and unlock switch: ON
No.
System state
Switching condition
SEC-198
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
Armed Phase
VEHICLE SECURITY SYSTEM switches to the ARMED phase from the PRE-ARMED phase after approxi-
mately 20 seconds, and blinks security indicator lamp slowly.
Alarm Phase
• VEHICLE SECURITY SYSTEM activates siren for approximately 27.5 seconds when any of the following
conditions is fulfilled while VEHICLE SECURITY SYSTEM is in the ARMED phase.
- When any door or hood is open
- When power supply to siren control unit is blocked
- When intruder sensor detects an attempt to enter into passenger compartment
- When battery connection is disconnected
• VEHICLE SECURITY SYSTEM deactivates siren when door is unlocked by Key fob or ignition switch is turn
ON position while siren is activated.
• VEHICLE SECURITY SYSTEM switches to the ARMED phase automatically when approximately 5 sec-
onds pass after deactivating siren.
SENSOR CANCEL FUNCTION
Perform the following procedure to deactivate intruder sensor.
1.
CHECK SENSOR CANCEL FUNCTION
1.
Turn ignition switch OFF.
2.
Press sensor cancel switch, and before 5 minutes pass, close all doors and hood, and lock all doors using
the Key fob.
3.
Check that VEHICLE SECURY SYSTEM is switched to the PRE-ARMED phase and that the siren sounds
one beep.
NOTE:
Intruder sensor is not cancelled and return to normal operation when any of the following conditions is fulfilled
while the cancellation procedure is being performed.
• When ignition switch turns ON.
• When 5 minutes or more pass after pressing sensor cancel switch.
• When VEHICLE SECURITY SYSTEM switches to the DISARMED phase.
Does security indicator lamp blink quickly?
YES
>> INSPECTION END
NO
>> Check again.
DIAGNOSIS SYSTEM (BCM)
SEC-199
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010479873
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
PTC heater control
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
SEC-200
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 3)
INFOID:0000000010827936
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT screen item
Indication/Unit
Description
BATTERY VOLTAGE
V
Battery voltage of the moment a particular DTC is detected.
VEHICLE SPEED
km/h
Vehicle speed of the moment a particular DTC is detected.
EXTERNAL TEMP
°
C
External temperature of the moment a particular DTC is detected
VEHICLE COND
—
NOTE:
This item is displayed, but cannot be use this item.
DOOR LOCK STATUS
—
NOTE:
This item is displayed, but cannot be use this item.
POWER SUPPLY
COUNTER
min
Displays the cumulative time from the time that the battery terminal is connected.
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
DIAGNOSIS SYSTEM (BCM)
SEC-201
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)
INFOID:0000000010827938
WORK SUPPORT
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
SEC-202
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
DIAGNOSIS SYSTEM (BCM)
SEC-203
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 6)
INFOID:0000000010827940
WORK SUPPORT
DATA MONITOR
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: S mode (horn non-operation)
• Off: C mode (horn operate)
ANSWER BACK KEYLESS
LOCK UNLOCK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: Horn and hazard warning lamp operate
• Off: Only hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
SEC-204
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
DIAGNOSIS SYSTEM (BCM)
SEC-205
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT) (Without Intelligent Key System)
INFOID:0000000010479871
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
WORK SUPPORT
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL UN-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL SW-TR
NOTE:
This item is indicated, but not monitored.
SEN CANCEL SW
Indicates [ON/OFF] condition of sensor cancel switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is indicated, but not monitored.
KEY SW
NOTE:
This item is indicated, but not monitored.
SEC-206
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
IMMU
IMMU : CONSULT Function (BCM - IMMU) (Without Intelligent Key System)
INFOID:0000000010479872
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
WORK SUPPORT
ACTIVE TEST
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change vehicle security alarm ON-OFF setting.
SIREN SET
Select the siren function ON or OFF, and siren type.
• MODE 1: Without siren
• MODE 2: With siren
• MODE 3: With external complete protection (with siren)
• MODE 4: Without any external protection (with siren)
• MODE 5: Without external tilt protection (with siren)
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
SIREN
Activates the self-diagnosis function for siren control unit.
VEHICLE SECURITY HORN
NOTE:
This item is indicated, but not used
HEAD LAMP
NOTE:
This item is indicated, but not used
Monitor item
Content
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen touched.
DIAGNOSIS SYSTEM (SIREN CONTROL UNIT)
SEC-207
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (SIREN CONTROL UNIT)
Diagnosis Description
INFOID:0000000010479870
DIAGNOSIS FUNCTION
Siren control unit has a self-diagnosis function which displays the diagnosis results for the following items.
• Circuit diagnosis: Displays if malfunction exists or not in the circuits between siren control unit and BCM or
siren control unit and sensors.
- Circuits are normal: Hazard warning lamp blinks 3 times.
- Circuit is malfunctioning: Hazard warning lamp does not blink.
• Alarm history: Displays alarm activation history for the maximum 3 items.
- Siren sounds for 0.4 seconds and sound interval is 0.4 seconds.
- When multiple symptoms exist, the interval between each alarm history is 2 seconds.
• Component diagnosis: Displays malfunctioning component (siren control unit or intruder sensor).
- Siren sounds for 1 second and sound interval is 0.4 seconds.
- When multiple symptoms exist, the interval between each diagnosis result is 2 seconds.
SELF-DIAGNOSIS PROCEDURE
1.
Connect CONSULT.
2.
Turn ignition switch ON.
3.
Select “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
4.
Select “SIREN” and touch “ON” to start self-diagnosis.
5.
Self-diagnosis result is displayed after 2 seconds.
SELF-DIAGNOSIS RESULT DISPLAY
Number of siren sounds
Cause of alarm activation
0
History is not found
1
Battery is disconnected and connected
2
Movement to enter into passenger room is detected
3
Communication between BCM and siren control unit is interrupted
4
Door or hood is opened
5
Difference of ID recognition between siren control unit and BCM
6
Communication between siren control unit and intruder sensor is interrupted
Number of siren sounds
Malfunctioning component
0
Malfunctioning component is not found
1
Siren control unit
2
Intruder sensor
SEC-208
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (SIREN CONTROL UNIT)
Self-diagnosis is performed as shown in the figure.
DIAGNOSIS PROCEDURE
Precaution for Diagnosis Procedure
• Self-diagnosis result is erased from siren control unit when setting alarm system after performing the self-
diagnosis.
- When performing self-diagnosis, it is advised to record the self-diagnosis result display on a memo pad.
- When replacing siren control unit, never set alarm system after performing the self-diagnosis.
JMKIB1922GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст