Qashqai J11. Security control system — part 3
DIAGNOSIS SYSTEM (BCM)
SEC-33
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
Monitor Item
Condition
SEC-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
DIAGNOSIS SYSTEM (BCM)
SEC-35
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
SEC-36
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)
INFOID:0000000010698094
WORK SUPPORT
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANSWER BACK
Reminder function (door request switch and Intelligent Key) mode can be selected from the
following with this mode
• On: S mode (buzzer or horn reminder non-operation)
• Off: C mode (buzzer or horn operate)
ANSWER BACK I-KEY LOCK UN-
LOCK
Reminder function (door request switch) mode can be selected from the following with this
mode
• BUZZER: Sound Intelligent Key warning buzzer
• HORN: Sound horn
• Off: Only hazard warning lamp operate
• INVALID: This item is displayed, but cannot be used
ANSWER BACK KEYLESS LOCK
UNLOCK
Reminder function (Intelligent Key) mode can be selected from the following with this mode
• On: Horn and hazard warning lamp operate
• Off: Only hazard warning lamp operate
DIAGNOSIS SYSTEM (BCM)
SEC-37
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
SEC-38
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANICE ALARM signal from Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
DIAGNOSIS SYSTEM (BCM)
SEC-39
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
SEC-40
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 3)
INFOID:0000000010827933
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
DIAGNOSIS SYSTEM (BCM)
SEC-41
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
SEC-42
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 4)
INFOID:0000000010827934
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK KEYLESS
LOCK UNLOCK
NOTE:
This item is displayed, but cannot be used
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DIAGNOSIS SYSTEM (BCM)
SEC-43
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 6)
INFOID:0000000010827935
WORK SUPPORT
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
NOTE:
This item is indicated, but not monitored
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
SEC-44
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: S mode (horn non-operation)
• Off: C mode (horn operate)
ANSWER BACK KEYLESS
LOCK UNLOCK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: Horn and hazard warning lamp operate
• Off: Only hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
DIAGNOSIS SYSTEM (BCM)
SEC-45
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT) (With Intelligent Key System)
INFOID:0000000010337879
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
SEC-46
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
ACTIVE TEST
IMMU
IMMU : CONSULT Function (BCM - IMMU) (With Intelligent Key System)
INFOID:0000000010337880
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
WORK SUPPORT
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL UN-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL SW-TR
NOTE:
This item is indicated, but not monitored.
SEN CANCEL SW
Indicates [ON/OFF] condition of sensor cancel switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is indicated, but not monitored.
KEY SW
NOTE:
This item is indicated, but not monitored.
Monitored Item
Description
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change vehicle security alarm ON-OFF setting.
SIREN SET
Select the siren function ON or OFF, and siren type.
• MODE 1: Without siren
• MODE 2: With siren
• MODE 3: With external complete protection (with siren)
• MODE 4: Without any external protection (with siren)
• MODE 5: Without external tilt protection (with siren)
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
SIREN
Activates the self-diagnosis function for siren control unit.
VEHICLE SECURITY HORN
NOTE:
This item is indicated, but not used
HEAD LAMP
NOTE:
This item is indicated, but not used
Monitor item
Content
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
DIAGNOSIS SYSTEM (BCM)
SEC-47
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ACTIVE TEST
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen touched.
SEC-48
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (SIREN CONTROL UNIT)
DIAGNOSIS SYSTEM (SIREN CONTROL UNIT)
Diagnosis Description
INFOID:0000000010450408
DIAGNOSIS FUNCTION
Siren control unit has a self-diagnosis function which displays the diagnosis results for the following items.
• Circuit diagnosis: Displays if malfunction exists or not in the circuits between siren control unit and BCM or
siren control unit and sensors.
- Circuits are normal: Hazard warning lamp blinks 3 times.
- Circuit is malfunctioning: Hazard warning lamp does not blink.
• Alarm history: Displays alarm activation history for the maximum 3 items.
- Siren sounds for 0.4 seconds and sound interval is 0.4 seconds.
- When multiple symptoms exist, the interval between each alarm history is 2 seconds.
• Component diagnosis: Displays malfunctioning component (siren control unit or intruder sensor).
- Siren sounds for 1 second and sound interval is 0.4 seconds.
- When multiple symptoms exist, the interval between each diagnosis result is 2 seconds.
SELF-DIAGNOSIS PROCEDURE
1.
Connect CONSULT.
2.
Turn ignition switch ON.
3.
Select “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.
4.
Select “SIREN” and touch “ON” to start self-diagnosis.
5.
Self-diagnosis result is displayed after 2 seconds.
SELF-DIAGNOSIS RESULT DISPLAY
Number of siren sounds
Cause of alarm activation
0
History is not found
1
Battery is disconnected and connected
2
Movement to enter into passenger room is detected
3
Communication between BCM and siren control unit is interrupted
4
Door or hood is opened
5
Difference of ID recognition between siren control unit and BCM
6
Communication between siren control unit and intruder sensor is interrupted
Number of siren sounds
Malfunctioning component
0
Malfunctioning component is not found
1
Siren control unit
2
Intruder sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст