Qashqai J11. Security control system — part 17
B2198 NATS ANTENNA AMP.
SEC-257
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
REPLACE BCM
BCS-135, "Removal and Installation"
.
>> INSPECTION END
BCM
Ground
Continuity
Connector
Terminal
M69
113
Not existed
109
SEC-258
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC Logic
INFOID:0000000010479761
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine.
-
Selector lever: In the P position
-
Brake pedal: Depressed
2.
Wait 1 second after engine started.
3.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-258, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479762
1.
CHECK DTC OF IPDM E/R
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
DTC No.
CONSULT screen items
DTC detecting condition
B2608
STARTER RELAY
BCM outputs starter relay OFF signal but BCM receives starter relay
ON signal from IPDM E/R (CAN).
B260F ENGINE STATUS
SEC-259
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B260F ENGINE STATUS
DTC Logic
INFOID:0000000010479763
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• ECM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B260F is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or
U1010.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000: Refer to
U1010: Refer to
NO
>> GO TO 2
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 2 seconds or more.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-259, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479764
1.
CHECK DTC PRIORITY
If DTC B260F is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or
U1010.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000: Refer to
U1010: Refer to
NO
>> GO TO 2
2.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B260F. Refer to
.
Is DTC detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
REPLACE ECM
Replace ECM.
Refer to the following procedure.
DTC No.
CONSULT screen items
DTC detecting condition
B260F
ENG STATE SIG LOST
BCM has not yet received the engine status signal from ECM when
ignition switch is in the ON position.
SEC-260
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B260F ENGINE STATUS
• HRA2DDT:
ECH-320, "Removal and Installation"
ECK-398, "Removal and Installation"
• R9M:
EC9-409, "Removal and Installation"
• MR16DDT:
ECM-616, "Removal and Installation"
• MR20DD:
ECM-1031, "Removal and Installation"
>> INSPECTION END
B27D1 START CUT RELAY OFF
SEC-261
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B27D1 START CUT RELAY OFF
DTC Logic
INFOID:0000000010479767
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Starter control relay
• Harness or connectors
(Starter control relay circuit is shorted)
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions and wait 1 second or more.
-
Selector lever: In the P position.
-
Brake pedal: Depressed.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-261, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479768
1.
CHECK STARTER CONTROL RELAY INPUT SIGNAL
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 2
2.
CHECK STARTER CONTROL RELAY INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector and starter control relay connector.
2.
Check continuity between BCM harness connector and starter control relay harness connector.
3.
Check continuity between BCM harness connector and ground.
DTC
CONSULT screen items
DTC detecting condition
B27D1–00
START CUT RELAY OFF
When the starter relay/starter control relay status signal transmitted from IPDM E/R via
CAN communication is (OFF/OFF) after 0.5 seconds elapse, even though BCM is oper-
ating the starter control relay ON output.
(+)
(-)
Condition
Voltage
BCM
Connector
Terminal
E60
171
Ground
Engine cranking
0 - 0.5 V
Other than engine cranking
9 - 16 V
BCM
Starter control relay
Continuity
Connector
Terminal
Connector
Terminal
E60
171
F162
1
Existed
SEC-262
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B27D1 START CUT RELAY OFF
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK FUSE
Check that the following fuse is not blown
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 6
4.
CHECK STARTER CONTROL RELAY OUTPUT SIGNAL
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
NO
>> GO TO 5
5.
CHECK STARTER CONTROL RELAY OUTPUT SIGNAL CIRCUIT
1.
Check continuity between IPDM E/R harness connector and starter control relay harness connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness.
6.
CHECK STARTER CONTROL RELAY
Check starter control relay. Refer to
SEC-263, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Replace starter control relay.
7.
CHECK INTERMITTENT INCIDENT
BCM
Ground
Continuity
Connector
Terminal
E60
171
No Existed
Signal name
Fuse
Battery power supply
30A
L
(+)
(-)
Condition
Voltage
IPDM E/R
Connector
Terminal
F88
68
Ground
Other than engine
cranking
2 - 4 V
Engine cranking
6 - 16 V
IPDM E/R
Starter control relay
Continuity
Connector
Terminal
Connector
Terminal
F88
68
F162
3
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F88
68
Not existed
B27D1 START CUT RELAY OFF
SEC-263
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010479769
1.
CHECK STARTER CONTROL RELAY
1.
Disconnect starter control relay.
2.
Check continuity between starter relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace starter control relay.
SEF497Y
starter control relay
Condition
Continuity
Terminal
12 V direct current supply between terminals
and
Existed
No current supply
Not existed
SEC-264
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B27D2 START CUT RELAY ON
B27D2 START CUT RELAY ON
DTC Logic
INFOID:0000000010479770
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(Starter control relay circuit is shorted)
• Starter control relay
• BCM
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions and wait 1 second or more.
-
Selector lever: In the P position.
-
Brake pedal: Depressed.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-264, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479771
1.
CHECK STARTER CONTROL RELAY INPUT SIGNAL
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 2
2.
CHECK STARTER CONTROL RELAY INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector and starter control relay connector.
2.
Check continuity between BCM harness connector and starter control relay harness connector.
3.
Check continuity between BCM harness connector and ground.
DTC
CONSULT screen items
DTC detecting condition
B27D2–00
START CUT RELAY ON
When BCM starter control relay is in OFF status, and when the starter relay/starter con-
trol relay status signal is (ON/ON)
(+)
(-)
Condition
Voltage
BCM
Connector
Terminal
E60
171
Ground
Engine cranking
0 - 0.5 V
Other than engine cranking
9 - 16 V
BCM
Starter control relay
Continuity
Connector
Terminal
Connector
Terminal
E60
171
F162
1
Existed
B27D2 START CUT RELAY ON
SEC-265
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK FUSE
Check that the following fuse is not blown
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 6
4.
CHECK STARTER CONTROL RELAY OUTPUT SIGNAL
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
.
NO
>> GO TO 5
5.
CHECK STARTER CONTROL RELAY OUTPUT SIGNAL CIRCUIT
1.
Check continuity between IPDM E/R harness connector and starter control relay harness connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness.
6.
CHECK STARTER CONTROL RELAY
Check starter control relay. Refer to
SEC-263, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7
NO
>> Replace starter control relay.
7.
REPLACE BCM
BCM
Ground
Continuity
Connector
Terminal
E60
171
No Existed
Signal name
Fuse
Battery power supply
30A
L
(+)
(-)
Condition
Voltage
IPDM E/R
Connector
Terminal
F88
68
Ground
Other than engine
cranking
2 - 4 V
Engine cranking
6 - 16 V
IPDM E/R
Starter control relay
Continuity
Connector
Terminal
Connector
Terminal
F88
68
F162
3
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F88
68
Not existed
SEC-266
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B27D2 START CUT RELAY ON
Replace BCM.
BCS-135, "Removal and Installation"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 8
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010479772
1.
CHECK STARTER CONTROL RELAY
1.
Disconnect starter control relay.
2.
Check continuity between starter relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace starter control relay.
SEF497Y
starter control relay
Condition
Continuity
Terminal
12 V direct current supply between terminals
and
Existed
No current supply
Not existed
B27DA IPDM CAN COMM CIRCUIT
SEC-267
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B27DA IPDM CAN COMM CIRCUIT
DTC Logic
INFOID:0000000010479773
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(The CAN communication line is open or shorted.)
• IPDM E/R
• BCM
FAIL-SAFE
Inhibit steering lock
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B27DA is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000 or
U1010.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000: Refer to
U1010: Refer to
NO
>> GO TO 2
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following condition.
-
Selector lever: In the P position.
-
Brake pedal: Not depressed.
2.
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-267, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479774
1.
CHECK DTC PRIORITY
If DTC B27DA is displayed with DTC U1000 or U1010, first perform the trouble diagnosis for DTC U1000
orU1010.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000: Refer to
NO
>> GO TO 2
2.
CHECK DTC OF IPDM E/R
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT. Refer to
.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 3
3.
REPLACE IPDM E/R
Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
.
Is the inspection result normal?
DTC
CONSULT screen items
DTC detecting condition
B27DA–00
IPDM CAN COMM CIRCUIT
When BCM cannot detect CAN communication with IPDM E/
R.
SEC-268
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B27DA IPDM CAN COMM CIRCUIT
YES
>> INSPECTION END
NO
>> GO TO 4
4.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 5
5.
REPLACE BCM
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
>> INSPECTION END
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
B20DF STARTER RELAY OFF CIRCUIT
SEC-269
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B20DF STARTER RELAY OFF CIRCUIT
DTC Logic
INFOID:0000000010479776
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(Starter relay circuit is open or shorted)
• IPDM E/R
• Starter motor
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions, and wait 2 seconds or more.
-
Selector lever: In the P position
-
Brake pedal: Depressed
2.
Check DTC in “Self Diagnosis Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-269, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010479777
1.
CHECK “S” TERMINAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect starter motor connector.
3.
Shift selector lever to “P“or ”N” position.
4.
Check voltage between starter motor harness connector and ground.
Other than MR engine models
MR engine models
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
REPLACE STARTER MOTOR
DTC
CONSULT screen items
DTC detecting condition
B20DF
STARTER RELAY
OFF CIRCUIT
[Ground short circuit/
disconnection]
When IPDM E/R performs starter relay ON output but starter
relay is OFF.
(+)
(-)
Condition
Voltage
Starter motor
Connector
Terminal
F104
1
Ground
When the ignition
switch is in START po-
sition
12 V or more
(+)
(-)
Condition
Voltage
Starter motor
Connector
Terminal
F106
1
Ground
When the ignition
switch is in START po-
sition
12 V or more
SEC-270
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B20DF STARTER RELAY OFF CIRCUIT
Replace starter motor. Refer to the following procedure.
• HRA2DDT:
STR-25, "HRA2DDT : Removal and Installation"
• MR20DE:
STR-28, "MR20DD : Removal and Installation"
STR-33, "K9K : Removal and Installation"
• R9M:
STR-34, "R9M : Removal and Installation"
>> INSPECTION END
3.
CHECK STARTER MOTER INPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between starter motor harness connector and IPDM E/R harness connector.
Other than MR engine models
MR engine models
4.
Check continuity between starter motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
REPLACE IPDM E/R
Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
>> INSPECTION END
Starter motor
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F104
1
F88
65
Existed
Starter motor
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F106
1
F88
65
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
F88
65
Not existed
POWER SUPPLY AND GROUND CIRCUIT
SEC-271
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
SIREN CONTROL UNIT
SIREN CONTROL UNIT : Diagnosis Procedure
INFOID:0000000010479798
1.
CHECK FUSE
Check that the following fuse is not blown.
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect siren control unit connector.
3.
Check voltage between siren control unit harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between siren control unit harness connectors and the ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
Signal name
Fuse
Battery power supply
20 (5 A)
(+)
(
−
)
Voltage
(Approx.)
Siren control unit
Connector
Terminal
Ground
B27
2
Battery voltage
Siren control unit
Ground
Continuity
Connector
Terminal
B27
5
Existed
SEC-272
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000010827161
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
SEC-169, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010479799
1.
CHECK FUSE
1.
Turn power switch OFF.
2.
Check that the following fuse in the fuse block (J/B) is not blown.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the cause of blowing.
2.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Disconnect combination meter connector.
2.
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect combination meter connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
REPLACE BCM
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminates
OFF
Does not illuminate
Signal name
Fuse No.
Battery power supply
21 (10 A)
(+)
(–)
Voltage (V)
(Approx.)
Combination meter
Connector
Terminal
M52
45
Ground
Battery voltage
(+)
(–)
Voltage
BCM
Connector
Terminal
M70
75
Ground
9 - 16 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст