Qashqai J11. Security control system — part 18
SECURITY INDICATOR LAMP
SEC-273
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
BCS-135, "Removal and Installation"
.
>> INSPECTION END
5.
CHECK SECURITY INDICATOR LAMP CIRCUIT
1.
Disconnect combination meter connector.
2.
Check continuity between combination meter harness connector and BCM harness connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-86, "Removal and Installation"
NO
>> Repair or replace harness.
Combination meter
BCM
Continuity
Connector
Terminal
Connector
Terminal
M51
7
M70
75
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M51
7
Not existed
SEC-274
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD SWITCH
HOOD SWITCH
Component Function Check
INFOID:0000000010479778
1.
CHECK FUNCTION
1.
Select “HOOD SW” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
2.
Check “HOOD SW” indication under the following condition.
Is the indication normal?
YES
>> Hood switch is OK.
NO
>> Refer to
SEC-274, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010479779
1.
CHECK HOOD SWITCH SIGNAL CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check voltage between hood switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK HOOD SWITCH SIGNAL CIRCUIT 2
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and hood switch harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK HOOD SWITCH GROUND CIRCUIT
Check continuity between hood switch harness connector and ground.
Monitor item
Condition
Indication
HOOD SW
Hood
Open
ON
Close
OFF
(+)
(–)
Voltage
Hood switch
Connector
Terminal
E100
2
Ground
9 - 16 V
IPDM E/R
Hood switch
Continuity
Connector
Terminal
Connector
Terminal
E102
60
E100
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E102
60
Not existed
Hood switch
Ground
Continuity
Connector
Terminal
E100
2
Existed
HOOD SWITCH
SEC-275
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK HOOD SWITCH
SEC-275, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace hood switch. Refer to
DLK-179, "HOOD LOCK : Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010479780
1.
CHECK HOOD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check continuity between hood switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hood switch. Refer to
DLK-179, "HOOD LOCK : Removal and Installation"
Hood switch
Condition
Continuity
Terminal
1
2
Hood lock
Unlock condition
Not existed
Lock condition
Existed
SEC-276
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Diagnosis Procedure
INFOID:0000000010479781
1.
CHECK HORN FUNCTION
Check that horns function properly using horn switch.
Does horn sound?
YES
>> GO TO 2.
NO
>> Check horn circuit. Refer to
2.
CHECK HORN CONTROL CIRCUIT
1.
Disconnect horn relay.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and horn relay harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-68, "Removal and Installation"
NO
>> Repair or replace harness.
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E37
9
E22
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E37
9
Not existed
INTRUDER SENSOR
SEC-277
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
INTRUDER SENSOR
Component Function Check
INFOID:0000000010479782
1.
CHECK INTRUDER SENSOR FUNCTION
1.
Turn ignition switch OFF.
2.
Check that hood is closed completely.
3.
Get in the vehicle and close all doors.
4.
Lock doors using Keyfob.
5.
Check security indicator lamp blinks to confirm that the vehicle security system is shifted into the ARMED
phase. Refer to
SEC-195, "VEHICLE SECURITY SYSTEM : System Description"
.
6.
Hold up and move a hand over intruder sensor.
7.
Check that siren sounds after a few seconds.
Does the siren sound?
YES
>> Intruder sensor is OK.
NO
>> Refer to
SEC-277, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010479783
1.
CHECK INTRUDER SENSOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect intruder sensor connector.
3.
Check voltage between intruder sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No. 79, located in the fuse block].
NO-2
>> Check harness for open or short between fuse and intruder sensor.
2.
CHECK INTRUDER SENSOR SIGNAL CIRCUIT
1.
Disconnect siren control unit connector.
2.
Check continuity between siren control unit harness connector and intruder sensor harness connector.
3.
Check continuity between siren control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTRUDER SENSOR GROUND CIRCUIT
Check continuity between intruder sensor harness connector and ground.
(+)
(–)
Voltage
(Approx.)
Sensor cancel switch
Connector
Terminal
R2
1
Ground
Battery voltage
Siren control unit
Sensor cancel switch
Continuity
Connector
Terminal
Connector
Terminal
B27
4
R2
2
Existed
Siren control unit
Ground
Continuity
Connector
Terminal
B27
4
Not existed
SEC-278
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
INTRUDER SENSOR
Is the inspection result normal?
YES
>> Replace intruder sensor.
NO
>> Repair or replace harness.
Sensor cancel switch
Ground
Continuity
Connector
Terminal
R2
3
Existed
SENSOR CANCEL SWITCH
SEC-279
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SENSOR CANCEL SWITCH
Diagnosis Procedure
INFOID:0000000010479784
1.
CHECK SENSOR CANCEL SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sensor cancel switch connector.
3.
Check signal between sensor cancel switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SENSOR CANCEL SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and sensor cancel switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between sensor cancel switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SENSOR CANCEL SWITCH
SEC-280, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
(+)
(–)
Voltage
Sensor cancel switch
Connector
Terminal
R2
5
Ground
JPMIA0011GB
BCM
Sensor cancel switch
Continuity
Connector
Terminal
Connector
Terminal
M69
107
R2
5
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
107
Not existed
Sensor cancel switch
Ground
Continuity
Connector
Terminal
R2
5
Existed
SEC-280
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
SENSOR CANCEL SWITCH
NO
>> Replace sensor cancel switch.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010479785
1.
CHECK SENSOR CANCEL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sensor cancel switch connector.
3.
Check continuity between sensor cancel switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sensor cancel switch.
Sensor cancel switch
Condition
Continuity
Terminal
5
6
Sensor cancel switch
Press
Existed
Release
Not existed
SIREN CONTROL UNIT CIRCUIT (COMMUNICATION SIGNAL)
SEC-281
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SIREN CONTROL UNIT CIRCUIT (COMMUNICATION SIGNAL)
Component Function Check
INFOID:0000000010479786
1.
CHECK SIREN CONTROL UNIT FUNCTION
1.
Turn ignition switch OFF.
2.
Check that hood is closed completely.
3.
Get in the vehicle and close all doors.
4.
Lock doors using Keyfob.
5.
Check security indicator lamp blinks to confirm that the vehicle security system is shifted into the ARMED
phase. Refer to
SEC-195, "VEHICLE SECURITY SYSTEM : System Description"
.
Is the inspection result normal?
YES
>> Siren control unit circuit (communication signal) is OK.
NO
>> Refer to
SEC-281, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010479787
1.
CHECK SIREN CONTROL UNIT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect siren control unit connector.
3.
Disconnect BCM connector.
4.
Check continuity between siren control unit harness connector and BCM harness connector.
5.
Check continuity between siren control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Siren control unit
BCM
Continuity
Connector
Terminal
Connector
Terminal
B27
3
B4
38
Existed
Siren control unit
Ground
Continuity
Connector
Terminal
B27
3
Not existed
SEC-282
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
SIREN CONTROL UNIT CIRCUIT (HAZARD SWITCH SIGNAL)
SIREN CONTROL UNIT CIRCUIT (HAZARD SWITCH SIGNAL)
Component Function Check
INFOID:0000000010479788
1.
CHECK SIREN CONTROL UNIT FUNCTION
1.
Turn ignition switch OFF.
2.
Check that hood is closed completely.
3.
Get in the vehicle and close all doors.
4.
Lock doors using Keyfob.
5.
Check security indicator lamp blinks to confirm that the vehicle security system is shifted into the ARMED
phase. Refer to
SEC-195, "VEHICLE SECURITY SYSTEM : System Description"
.
6.
Hold up and move a hand over intruder sensor.
7.
Check that hazard warning lamps blinks after a few seconds.
Does the siren sound?
YES
>> Siren control unit circuit (hazard switch signal) is OK.
NO
>> Refer to
SEC-282, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010479789
1.
CHECK SIREN CONTROL UNIT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect siren control unit connector.
3.
Disconnect BCM connector.
4.
Check continuity between siren control unit harness connector and BCM harness connector.
5.
Check continuity between siren control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Siren control unit
BCM
Continuity
Connector
Terminal
Connector
Terminal
B27
1
M70
51
Existed
Siren control unit
Ground
Continuity
Connector
Terminal
B27
1
Not existed
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SEC-283
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000010338082
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Ignition switch is not in the ON position.
Diagnosis Procedure
INFOID:0000000010505355
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-169, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
BCS-135, "Removal and Installation"
.
Is the result normal?
YES
>> INSPECTION END.
NO
>> GO TO 3
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
SEC-284
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
VEHICLE SECURITY SYSTEM CANNOT BE SET
KEY FOB
KEY FOB : Description
INFOID:0000000010338084
Armed phase is not activated when all doors are locked using keyfob.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
KEY FOB : Diagnosis Procedure
INFOID:0000000010338085
1.
CHECK REMOTE KEYLESS ENTRY SYSTEM
Lock/unlock door with keyfob. Refer to
DLK-391, "REMOTE KEYLESS ENTRY FUNCTION : System Descrip-
(With super lock) or
(With out super lock).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-448, "Diagnosis Procedure"
.
2.
CHECK HOOD SWITCH
Check hood switch. Refer to
SEC-274, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000010338086
ARMED phase is not activated when door is locked using door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000010338087
1.
CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door lock and unlock switch. Refer to
or
Is the inspection result normal?
YES
>> GO TO 2.
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-285
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO
>> Check power door lock system (door lock function). Refer to
DLK-443, "ALL DOOR : Diagnosis
(With super lock) or
DLK-581, "ALL DOOR : Diagnosis Procedure"
(Without super
lock).
2.
CHECK HOOD SWITCH
Check hood switch. Refer to
SEC-274, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or Replace hood switch.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-135, "Removal and Installation"
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
UNLOCK SENSOR
UNLOCK SENSOR : Description
INFOID:0000000010506179
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
UNLOCK SENSOR : Diagnosis Procedure
INFOID:0000000010506180
1.
CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to
(Without super
lock).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system (door lock function). Refer to
DLK-447, "Diagnosis Procedure"
(With super lock) or
DLK-585, "Diagnosis Procedure"
(Without super lock).
2.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-274, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
SEC-286
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000010338088
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000010505375
1.
CHECK SENSOR CANCEL SWITCH
Check sensor cancel switch.
Refer to
SEC-279, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace sensor cancel switch.
2.
PERFORM SELF-DIAGNOSIS OF SIREN CONTROL UNIT
Perform self-diagnosis of siren control unit.
Refer to
SEC-207, "Diagnosis Description"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-430, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the malfunctioning door switch. Refer to
DLK-195, "Removal and Installation"
4.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-274, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace hood switch.
5.
CHECK INTRUDER SENSOR
Check intruder sensor.
Refer to
SEC-277, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace intruder sensor.
6.
REPLACE SIREN CONTROL UNIT
1.
Replace siren control unit.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 7.
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
SEC-287
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
7.
REPLACE BCM
BCS-135, "Removal and Installation"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
SEC-288
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
INTRUDER SENSOR CANNOT BE DEACTIVATED
INTRUDER SENSOR CANNOT BE DEACTIVATED
Diagnosis Procedure
INFOID:0000000010505376
1.
CHECK SENSOR CANCEL SWITCH
Check sensor cancel switch.
Refer to
SEC-279, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace sensor cancel switch.
2.
REPLACE SIREN CONTROL UNIT
1.
Replace siren control unit.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
REPLACE BCM
Replace BCM. Refer to
BCS-135, "Removal and Installation"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NATS ANTENNA AMP.
SEC-289
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000010338090
REMOVAL
1.
Remove the steering column cover.
Refer to
IP-13, "Removal and Installation"
.
2.
Disengage NATS antenna amp. fixing pawl and then remove
NATS antenna amp.
from steering lock assembly.
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIB2859ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст