Nissan X-Trail 32. Manual — part 1779
FRONT SEAT BELT
SB-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
1.
Remove front seat. Refer to
SE-41, "Removal and Installation"
.
2.
Disconnect seat belt buckle harness connector and disengage harness clip.
3.
Remove seat belt buckle mounting anchor bolt, and then remove seat belt buckle. Refer to
INSTALLATION
Install in the reverse order of removal.
SEAT BELT BUCKLE : Inspection
INFOID:0000000010927776
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attached hardware after any collision.
NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced
unless the collision was minor and the belts show no damage and continue to operate properly. Fail-
ure to do so could result in serious personal injury in an accident. Seat belt assemblies not in use dur-
ing a collision should also be replaced if either damage or improper operation was noted. Seat belt
pre-tensioners should be replaced even if the seat belts were not in use during a frontal collision in
which the air bags were deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt is in use at the time of a collision (except for minor collisions and the belts, retractors and buck-
les show no damage and continue to operate properly).
• The seat belt is damaged in an accident (i.e. torn webbing, bent retractor or guide, etc.).
• The seat belt attaching point is damaged in an accident. Inspect the seat belt attaching area for damage or
distortion and repair if necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The seat belt pre-tensioner must be replaced even if the seat belts were not in use during the collision in
which the air bags were deployed.
PRELIMINARY CHECKS
1.
Check the seat belt warning lamp for proper operation as per the following:
a.
Turn ignition switch ON. The seat belt warning lamp should illuminate.
b.
Fasten driver seat belt. The seat belt warning lamp should turn OFF.
2.
If the air bag warning lamp turns ON, perform self-diagnosis using CONSULT. Refer to
.
3.
Check that the seat belt retractor, seat belt anchor and buckle bolts are tightened firmly.
4.
Repeat steps above if necessary to check the other seat belts.
SB-16
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
REAR SEAT BELT
Exploded View
INFOID:0000000010927777
Sliding Seat Type
JMHIA2927GB
Seat belt finisher
Center seat belt retractor assembly
Anchor nut
Anchor bolt
Shoulder anchor cover
Shoulder anchor
Spacer
Retaining washer
Shoulder bracket
Seat belt retractor assembly LH/RH
Seat belt hook
Seat belt buckle (without seat belt re-
minder)
REAR SEAT BELT
SB-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
SEAT BELT RETRACTOR
SEAT BELT RETRACTOR : Removal and Installation
INFOID:0000000010927778
REMOVAL
Seat Belt Retractor LH/RH
1.
Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
2.
Remove shoulder anchor.
a.
Disengage shoulder anchor cover fixing pawls, and then remove
shoulder anchor cover.
b.
Remove shoulder anchor mounting anchor bolt, and then remove shoulder anchor.
3.
Remove seat belt retractor assembly mounting anchor bolt, and then remove seat belt retractor.
Center Seat Belt Retractor
1.
Remove seatback trim.
Sliding seat type: Refer to
SE-58, "SEATBACK : Disassembly and Assembly"
.
2.
Remove seat belt guide.
Sliding Seat Type
1.
Remove webbing guide.
Seat belt buckle (with seat belt re-
minder)
: Pawl
: N·m (kg-m, ft-lb)
: Pawl
JMHIA1725ZZ
JMHIA2891ZZ
SB-18
< REMOVAL AND INSTALLATION >
REAR SEAT BELT
2.
Remove seat belt guide mounting nuts
, and then remove
seat belt guide.
3.
Remove seat belt retractor mounting anchor nut, and then remove seat belt retractor.
INSTALLATION
Install in the reverse order of removal.
SEAT BELT RETRACTOR : Inspection
INFOID:0000000010927779
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attached hardware after any collision.
NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced
unless the collision was minor and the belts show no damage and continue to operate properly. Fail-
ure to do so could result in serious personal injury in an accident. Seat belt assemblies not in use dur-
ing a collision should also be replaced if either damage or improper operation was noted. Seat belt
pre-tensioners should be replaced even if the seat belts were not in use during a frontal collision in
which the air bags were deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt is in use at the time of a collision (except for minor collisions and the belts, retractors and buck-
les show no damage and continue to operate properly).
• The seat belt is damaged in an accident (i.e. torn webbing, bent retractor or guide, etc.).
• The seat belt attaching point is damaged in an accident. Inspect the seat belt attaching area for damage or
distortion and repair if necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
PRELIMINARY CHECKS
1.
Check the seat belt warning lamp for proper operation as per the following:
a.
Turn ignition switch ON. The seat belt warning lamp should illuminate.
b.
Fasten driver seat belt. The seat belt warning lamp should turn OFF.
2.
Check that the seat belt retractor, seat belt anchor and buckle bolts are tightened firmly.
3.
Check retractor operation:
a.
Fully extend the seat belt webbing and check for twists, tears or other damage.
b.
Allow the seat belt to retract. Check that webbing returns smoothly and completely into the retractor. If the
seat belt does not return smoothly, wipe the inside of the loops with a clean paper cloth. Dirt build-up in the
loops of that upper anchors can cause the seat belts to retract slowly.
4.
Repeat steps above if necessary to check the other seat belts.
SEAT BELT RETRACTOR ON-VEHICLE CHECK
Emergency Locking Retractors (ELR)
NOTE:
All seat belt retractors are Emergency Locking Retractors (ELR) type. In an emergency (sudden stop) the
retractor will lock and prevent the webbing from extending any further.
Check the seat belt retractors with the following test(s) to determine if a retractor assembly is operating prop-
erly.
ELR Function Stationary Check
JMHIA2892ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст