Nissan X-Trail 32. Manual — part 1233
REAR COMBINATION LAMP
EXL-389
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
6.
Disconnect rear combination lamp (body side) harness connec-
tor .
7.
Pull rear combination lamp (body side) toward vehicle rear to
disengage fixing clips, and then remove rear combination lamp
(body side).
INSTALLATION
Install in the reverse order of removal.
REAR COMBINATION LAMP (BODY SIDE) : Replacement
INFOID:0000000010789914
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-214, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
TAIL LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-388, "REAR COMBINATION LAMP (BODY
SIDE) : Removal and Installation"
.
2.
Rotate tail lamp bulb socket counterclockwise, and then remove tail lamp bulb socket.
3.
Remove tail lamp bulb from tail lamp bulb socket.
STOP LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-388, "REAR COMBINATION LAMP (BODY
SIDE) : Removal and Installation"
.
2.
Rotate stop lamp bulb socket counterclockwise, and then remove stop lamp bulb socket.
3.
Remove stop lamp bulb from stop lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-388, "REAR COMBINATION LAMP (BODY
SIDE) : Removal and Installation"
.
2.
Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
3.
Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
REAR COMBINATION LAMP (BACK DOOR SIDE)
JMLIA4968ZZ
: Clip
JMLIA4969ZZ
EXL-390
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
REAR COMBINATION LAMP (BACK DOOR SIDE) : Removal and Installation
INFOID:0000000010789915
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-214, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Fully open back door.
2.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
3.
Disconnect rear combination lamp (back door side) harness
connector .
4.
Remove rear combination lamp (back door side) mounting nuts
.
5.
Apply protective tape (A) on the part to protect it from damage.
6.
Disengage rear combination lamp (back door side) fixing clips
using a remover tool (A), and then remove rear combination
lamp (back door side).
INSTALLATION
JMLIA4970ZZ
JMLIA4971ZZ
JMLIA4972ZZ
: Clip
JMLIA4973ZZ
REAR COMBINATION LAMP
EXL-391
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Install in the reverse order of removal.
REAR COMBINATION LAMP (BACK DOOR SIDE) : Replacement
INFOID:0000000010789916
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-214, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
TAIL LAMP BULB
1.
Remove rear combination lamp (back door side). Refer to
EXL-390, "REAR COMBINATION LAMP
(BACK DOOR SIDE) : Removal and Installation"
2.
Rotate tail lamp bulb socket counterclockwise, and then remove tail lamp bulb socket.
3.
Remove tail lamp bulb from tail lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove rear combination lamp (back door side). Refer to
EXL-390, "REAR COMBINATION LAMP
(BACK DOOR SIDE) : Removal and Installation"
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
EXL-392
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000010789917
Removal and Installation
INFOID:0000000010789918
CAUTION:
Disconnect battery negative terminal or remove power circuit fuse when performing the operation for
preventing electric leakage. Refer to
EXL-214, "Precautions for Removing Battery Terminal"
.
REMOVAL
1.
Fully open back door.
2.
Apply protective tapes (A) on the part to protect it from damage.
High-mounted stop lamp
: N·m (kg-m, in-lb)
JMLIA4963GB
JMLIA4974ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст