Nissan X-Trail 32. Manual — part 1267
FAX-60
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT
4.
Install dust shields.
CAUTION:
Never reuse dust shields.
Dynamic Damper (If equipped)
• Put boot band in the groove on drive shaft boot. Then fit pawls (
)
into holes to temporary installation.
NOTE:
For the large diameter side, fit projection
and guide slit
at
first.
• Pinch projection on the band with suitable pliers to tighten band.
• Insert tip of band below end of the pawl.
• Secure dynamic damper with bands in the following specified posi-
tion when removing.
CAUTION:
Never reuse bands.
Wheel Side
For further details, refer to the installation procedure of “
FAX-27, "R9M : Removal and Installation"
” for the
drive shaft boot.
R9M : Inspection
INFOID:0000000010824394
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
JPDIF0127ZZ
SDIA3557E
SDIA3558E
Demission :
FAC0156D
FRONT DRIVE SHAFT
FAX-61
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are.
Dynamic Damper (If equipped)
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Transaxle Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
SDIA1190J
FAX-62
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010824395
Drive Shaft
INFOID:0000000010824396
MR20DD
CVT
*: For measuring position. Refer to
FAX-42, "MR20DD : Disassembly and Assembly"
M/T
*: For measuring position. Refer to
FAX-42, "MR20DD : Disassembly and Assembly"
R9M
CVT
*: For measuring position. Refer to
FAX-56, "R9M : Disassembly and Assembly"
.
M/T
Axial end play
0.05 mm (0.002 in) or less
Item
Standard
Left side
Right side
Grease quantity
Wheel side
115 – 135 g (4.06 – 4.76 oz)
Transaxle side
175 – 195 g (6.18 – 6.87 oz)
Boots installed length
*
Wheel side
141.5 mm (5.57 in)
Transaxle side
196.9 mm (7.75 in)
188.9 mm (7.44 in)
Dimension of dynamic damper
*
A
273 – 279 mm (10.75 – 10.98 in)
243 – 249 mm (9.57 – 9.80 in)
B
70 mm (2.76 in)
Item
Standard
Left side
Right side
Grease quantity
Wheel side
115 – 135 g (4.06 – 4.76 oz)
Transaxle side
175 – 195 g (6.18 – 6.87 oz)
Boots installed length
*
Wheel side
141.5 mm (5.57 in)
Transaxle side
202.1 mm (7.96 in)
188.9 mm (7.44 in)
Dimension of dynamic damper
*
A
273 – 279 mm (10.75 – 10.98 in)
243 – 249 mm (9.57 – 9.80 in)
B
70 mm (2.76 in)
Item
Standard
Left side
Right side
Grease quantity
Wheel side
145 – 165 g (5.11 – 5.82 oz)
Transaxle side
265 – 285 g (9.35 – 10.05 oz)
Boots installed length
*
Wheel side
145 mm (5.71 in)
Transaxle side
196.1 mm (7.72 in)
184.1 mm (7.25 in)
Dimension of dynamic damper
*
A
255 – 261 mm (10.04 – 10.28 in)
205 – 211 mm (8.07 – 8.31 in)
B
70 mm (2.76 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-63
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
*: For measuring position. Refer to
FAX-56, "R9M : Disassembly and Assembly"
.
Item
Standard
Left side
Right side
Grease quantity
Wheel side
145 – 165 g (5.11 – 5.82 oz)
Transaxle side
265 – 285 g (9.35 – 10.05 oz)
Boots installed length
*
Wheel side
145 mm (5.71 in)
Transaxle side
196.1 mm (7.72 in)
184.1 mm (7.25 in)
Dimension of dynamic damper
*
A
207 – 213 mm (8.15 – 8.39 in)
—
B
70 mm (2.76 in)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст