Nissan X-Trail 32. Manual — part 1473
HEADLINING
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
*1
: With rain sensor without front camera unit
*2
: With front camera unit
Removal and Installation
INFOID:0000000010730560
CAUTION:
Never damage the roof panel.
REMOVAL
1.
Remove front body side welt (LH and RH) and rear body side welt (LH and RH). Refer to
SIDE WELT : Removal and Installation"
2.
Remove front pillar garnish (LH and RH). Refer to
INT-23, "FRONT PILLAR GARNISH : Removal and
.
3.
Remove the following parts of front pillar LH.
• Disconnect harness connector
.
• Disconnect harness connector
.
• Disengage harness fixing clips.
4.
Remove center pillar upper garnish (LH and RH). Refer to
INT-28, "CENTER PILLAR UPPER GARNISH :
.
5.
Remove luggage side upper finisher (LH and RH). Refer to
INT-45, "LUGGAGE SIDE UPPER FINISHER
6.
Remove all assist grips.
a.
Disengage assist grip cap fixing pawl using a remover tool (A),
and then remove assist grip cap according to numerical order
1
→
2 indicated by arrows in the figure.
b.
Pull assist grip forward and remove it.
c.
Remove assist grip fixing metal clips remaining on the roof panel.
7.
Remove map lamp assembly. Refer to
INL-76, "MAP LAMP : Removal and Installation"
.
8.
Remove room lamp assembly. Refer to
INL-84, "Removal and Installation"
(normal roof models).
Map lamp assembly
Rain sensor cover
*1
Sun visor assembly RH
Sun visor cover RH
Sun visor holder RH
Camera/sensor cover RH
*2
Camera/sensor cover LH
*2
Sun visor assembly LH
Sun visor holder LH
Sun visor cover LH
Rear assist grip LH
Assist grip cap
Metal clip
: Clip
: Pawl
: Metal clip
: Clip
JMJIA9637ZZ
: Pawl
JMJIA8937ZZ
INT-38
< REMOVAL AND INSTALLATION >
HEADLINING
9.
Remove rain sensor cover. Refer to
WW-109, "Removal and Installation"
(with rain sensor without front
camera).
10. Remove camera/sensor cover (LH and RH). Refer to
DAS-149, "Removal and Installation"
(with front
camera).
11. Remove sun visor assembly (LH and RH).
a.
Disengage sun visor cover fixing pawls using a remover tool (A),
and then remove sun visor cover (LH and RH).
b.
Remove sun visor assembly fixing screws.
c.
Disconnect vanity mirror lamp harness connector, and then remove sun visor assembly (LH and RH).
12. Remove sun visor holder (LH and RH) using a remover tool (A)
according to numerical order 1
→
2 indicated by arrows as shown
in the figure.
13. Remove headlining assembly rear end fixing clips
.
14. Peel off dual-lock fasteners
between headlining assembly and roof panel (sunroof models).
CAUTION:
Never bend headlining when removing.
• Front side
: Pawl
JMJIA4399ZZ
JMJIA9251ZZ
JMJIA9638ZZ
: Vehicle front
JMJIA9639ZZ
HEADLINING
INT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Rear side
15. Remove headlining assembly from back door according to direc-
tion indicated by the arrow as shown in the figure.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing.
16. Remove assist grip bracket mounting bolts
, and then remove
assist grip bracket (sunroof models).
17. Remove personal lamp assembly after removing headlining assembly. Refer to
.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never bend headlining when installing.
• Be careful that the headlining surface is not wrinkled when installing.
• When installing assist grip, install metal clip
to assist grip
cap
, and then install to the body panel.
: Vehicle front
JMJIA9640ZZ
JMJIA9641ZZ
JMJIA9610ZZ
JMJIA3623ZZ
INT-40
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
LUGGAGE TRIM
Exploded View
INFOID:0000000010730561
Tonneau cover assembly
Luggage side upper finisher LH
Luggage side lower finisher LH
Front luggage side finisher bracket
LH
*1
Rear luggage side finisher bracket
LH
*1
Luggage floor carpet
*2
Rear luggage floor board LH
*1
Rear luggage floor board center
*1
Luggage rear plate mask
Luggage rear plate
Rear luggage floor board RH
*1
Luggage side lower finisher RH
Rear luggage side finisher bracket
RH
*1
Front luggage side finisher bracket
RH
*1
Luggage side upper finisher RH
Rope hook
Front luggage floor board
*1
Luggage side finisher lid LH
Luggage trim cap
*1
Luggage room lamp
Rear luggage floor board RH
*3
Rear luggage floor board center
*3
Rear luggage floor board LH
*3
Luggage floor carpet
*3
Luggage floor carpet
*4
JMJIB0201ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст