Nissan X-Trail 32. Manual — part 1546
LU-20
< PRECAUTION >
[QR25DE]
PRECAUTIONS
• After removing mounting nuts and bolts, separate the mating sur-
face using the seal cutter [SST: KV10111100] (A) and remove old
liquid gasket sealing.
CAUTION:
Never damage the mating surfaces.
• Tap the seal cutter [SST: KV10111100] to insert it
, and then
slide it
by tapping on the side as shown in the figure.
• In areas where the seal cutter [SST: KV10111100] is difficult to use,
lightly tap the parts using a plastic hammer to remove it.
CAUTION:
If for some unavoidable reason tool such as a screwdriver is
used, be careful not to damage the mating surfaces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper (A), remove old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2.
Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3.
Attach liquid gasket tube to the tube presser (commercial ser-
vice tool).
Use Genuine Liquid Gasket or equivalent.
4.
Apply liquid gasket without gaps to the specified location accord-
ing to the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
• As for bolt holes
, normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Check to read the text of this manual.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
JPBIA0052ZZ
JPBIA0053ZZ
EMA0622D
: Groove
: Inside
JPBIA0010ZZ
PREPARATION
LU-21
< PREPARATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010783303
Commercial Service Tools
INFOID:0000000010783304
Tool number
Tool name
Description
KV10111100
Seat cutter
Removing oil pan (lower) etc.
ST25051001
Oil pressure gauge
Measuring oil pressure
Maximum measuring range: 2,452 kPa
(24.52 bar, 25 kg/cm
2
, 356 psi)
ST25052000
Hose
Adapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrench
Removing and installing oil filter
a: 64.3 mm (2.531 in)
NT046
NT050
S-NT559
S-NT375
LU-22
< PREPARATION >
[QR25DE]
PREPARATION
Tool name
Description
Deep socket
Removing and installing oil pressure sensor
27 mm (1.06 in)
Tube presser
Pressing the tube of liquid gasket
PBIC4066E
NT052
DESCRIPTION
LU-23
< SYSTEM DESCRIPTION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SYSTEM DESCRIPTION
DESCRIPTION
Engine Lubrication System
INFOID:0000000010783305
JSBIA3413ZZ
Intake camshaft
Exhaust camshaft
Intake camshaft sprocket
Exhaust camshaft sprocket
Chain tensioner
Intermdeiate valve timing control so-
lenoid valve
Intake valve timing control solenoid
valve
Exhaust valve timing control sole-
noid valve
Oil cooler
Oil pressure sensor
Timing chain oil jet
Oil pump
Oil filter
Oil strainer
Balancer unit
Crankshaft
Timing chain oil jet
Main gallery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст