Nissan X-Trail 32. Manual — part 1101
DRIVE BELT
EM-301
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3.
Insert a stopper pin (A) in diameter such as short-length screw-
driver into the hole of the retaining boss to fix drive belt auto-ten-
sioner pulley.
• Keep drive belt auto-tensioner pulley arm locked after drive
belt is removed.
NOTE:
Use approximately 3.0 mm (0.118 in) dia. hard metal pin as a
stopper pin.
4.
Remove drive belt.
INSTALLATION
1.
Install drive belt.
CAUTION:
• Check that drive belt is completely set to pulleys.
• Check for engine oil, working fluid and engine coolant are not adhered to drive belt and each
pulley groove.
2.
Release drive belt auto-tensioner, and apply tension to drive belt.
3.
Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4.
Check that the indicator (notch on fixed side) of drive belt auto-tensioner is within the range when new
drive belt is installed. Refer to
.
Inspection
INFOID:0000000010784305
WARNING:
Be sure to perform this step when the engine is stopped.
• Check that the indicator
(notch on fixed side) of drive belt auto-tensioner is within the possible use range
.
NOTE:
• Check the drive belt auto-tensioner indication when the engine is cold.
• When new drive belt is installed, the indicator (notch on fixed side) should be within the range
in the fig-
ure.
• Visually check entire drive belt for wear, damage or cracks.
E1BIA0657ZZ
JPBIA6943ZZ
Water pump pulley
Drive belt auto-tensioner
Crankshaft pulley
A/C compressor
Drive belt
Idler pulley
Alternator
View
Indicator
Range when new drive belt is in-
stalled
Possible use range
EM-302
< PERIODIC MAINTENANCE >
[R9M]
DRIVE BELT
• If the indicator (notch on fixed side) is out of the possible use range or belt is damaged, replace drive belt.
CAUTION:
Drive belt auto-tensioner and idler pulley must be replaced with new ones when the drive belt is
replaced.
Adjustment
INFOID:0000000010784306
AIR CLEANER FILTER
EM-303
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER FILTER
Exploded View
INFOID:0000000011004806
Removal and Installation
INFOID:0000000010784308
REMOVAL
1.
To remove air duct 2
, pinch pawl
to unlock, move pawl
frontward, and remove air duct 2 upward.
JPBIA6926GB
Air duct
Mass air flow sensor
Collar
Grommet
Air cleaner body
Mounting rubber
Bracket
Air cleaner filter
Air cleaner cover
Air duct 2
Air duct 1
To turbochager
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Vehicle front
JSBIA4626ZZ
EM-304
< PERIODIC MAINTENANCE >
[R9M]
AIR CLEANER FILTER
2.
Remove the clips
of air cleaner cover
.
3.
Shift air cleaner cover
to vehicle front side and remove air
cleaner filter
.
INSTALLATION
Install in the reverse order of removal.
• Insert the projection
of air cleaner filter
in such a way so that
it becomes the position (upper front side of car) of illustration.
• Verify that there is no looseness in air cleaner cover and has been fixed accurately.
• Check that pawls
and
(3 in total) of air duct 2
are engaged.
Inspection (Dry Paper Type)
INFOID:0000000011004807
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• To clean air cleaner element, blow it from intake manifold side towards air intake side to remove trash or
dust.
• If clogging or damage is observed, replace the air cleaner element.
: Vehicle front
JPBIA6829ZZ
: Projection
JPBIA6830ZZ
: Air cleaner cover
JPBIA6830ZZ
: Vehicle front
JPBIA6828ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст