Nissan X-Trail 32. Manual — part 434
DIAGNOSIS SYSTEM (BCM)
DLK-77
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intel-
ligent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/On] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC
(CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
Monitor Item
Condition
DLK-78
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
Indicates [On/Off] condition of back door open request signal from Intelligent Key
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: [Intelligent Key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
DIAGNOSIS SYSTEM (BCM)
DLK-79
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK) (With Intelligent Key System and Super
Lock)
INFOID:0000000010708059
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be used
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
DETECTION SENSOR (BK)
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OPENER SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
DLK-80
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
CONSULT Function (AUTOMATIC BACK DOOR CONTROL UNIT)
INFOID:0000000010708060
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with automatic back door control unit.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Diagnosis mode
Function Description
Work Support
Changes the setting for system function
Self Diagnostic Result
Displays the diagnosis results judged by automatic back door control unit
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from automatic back door
control unit
Data Monitor
The automatic back door control unit input/output signals are displayed
Ecu Identification
The automatic back door control unit part number is displayed
Monitor Item
Description
SPINDLE SENSOR LH
Indicates [Pulse] condition of encoder LH
SPINDLE LH SPEED
Indicates [mm/s] condition of spindle motor LH operation speed
SPINDLE MOTOR LH DUTY
Indicates [%] condition of spindle motor LH duty
VHCL SPEED MTR
Display the vehicle speed signal received from unified meter and A/C amp. by numerical
value [km/h]
VHCL SPEED ABS
Display the vehicle speed signal received from ABS actuator and electrical unit by numer-
ical value [km/h]
MAIN SW
Indicates [ON/OFF] condition of automatic back door main switch
AUTO BD SW
Indicates [ON/OFF] condition of automatic back door switch
BK DOOR CL SW
Indicates [ON/OFF] condition of automatic back door close switch
PKB SW
Indicates [ON/OFF] condition of parking brake status from combination meter via CAN
communication
BACK DOOR LOCK STATUS
Indicates [ON/OFF] condition of back door lock status
OPEN SW
Indicates [ON/OFF] condition of open switch
CLOSE SW
Indicates [ON/OFF] condition of close switch
HALF LATCH SW
Indicates [ON/OFF] condition of half latch switch
TOUCH SEN RH
Indicates [ON/OFF/OPEN] condition of touch sensor RH
TOUCH SEN LH
Indicates [ON/OFF/OPEN] condition of touch sensor LH
P RANGE IND
Indicates [ON/OFF] condition of P range signal from unified meter and A/C amp.
RKE REQ
Indicates [OFF/MOVE/REV] condition of remote keyless entry signal from BCM
IGN SW
Indicates [ON/OFF] condition of IGN power supply
SPINDLE LH ENCODER A
Indicates [LO/HI] condition of encoder signal A from encoder LH
SPINDLE LH ENCODER B
Indicates [LO/HI] condition of encoder signal B from encoder LH
UNLOCK SEN BD
NOTE:
This item is displayed, but cannot be monitored
DESTINATION
Indicates [Type 1/Type 2/Type 3/Type 4] specification of destination of the automatic back
door system
Normal: [Type 3] is monitored
TRANSMISSION TYPE
Indicates [MT/(AT/CVT)] type of transmission
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст