Nissan X-Trail 32. Manual — part 1240
REAR BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REMOVAL
1.
Fully open back door.
2.
Remove back side of rear fillet molding (LH and RH). Refer to
EXT-33, "REAR FILLET MOLDING :
.
3.
Remove rear bumper fascia fixing screws
of bumper upper
side.
4.
Remove rear bumper fascia fixing clips
of bumper lower side.
5.
Remove rear bumper fascia mounting bolt
and fixing clip
lower side of bumper both end.
6.
Remove rear bumper fascia mounting bolt
(LH and RH).
JMKIB2798ZZ
JMKIB2799ZZ
: Vehicle front
JMKIB2800ZZ
JMKIB2801ZZ
EXT-20
< REMOVAL AND INSTALLATION >
REAR BUMPER
7.
Apply protective tape (A) on the part to protect it from damage.
8.
Pull rear bumper fascia side toward the vehicle side to disen-
gage the fitting of rear bumper side bracket and rear bumper
fascia side according to the numerical order 1
→
3 as shown by
the arrows in the figure.
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
9.
Disconnect rear fog lamp harness connector. (if equipped)
10. Disconnect rear sonar sensor harness connector. (if equipped)
11. Remove rear bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
12. Remove the following parts after removing rear bumper fascia assembly.
• Rear fog lamp. Refer to the following. (if equipped)
- LED HEADLAMP: Refer to
EXL-211, "Removal and Installation"
- HALOGEN HEADLAMP: Refer to
EXL-396, "Removal and Installation"
• Rear sonar sensor. Refer to the following. (if equipped)
- WITH PARK ASSIST: Refer to
SN-240, "REAR : Removal and Installation"
- WITHOUT PARK ASSIST: Refer to
SN-114, "REAR : Removal and Installation"
• Reflex reflector. Refer to
EXL-212, "Removal and Installation"
.
• Rear bumper finisher. (if equipped)
13. Remove rear bumper reinforcement mounting nuts, and then remove rear bumper reinforcement.
14. Remove rear bumper stay mounting bolts, and then remove rear bumper stay (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
JMKIB2802ZZ
: Pawl
JMKIB2803ZZ
JMKIB2804ZZ
REAR BUMPER
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Portion
Clearance
Surface height difference
Rear bumper fascia – Back door
panel
–
5.5 – 9.5 mm
(0.217 – 0.374 in)
—
–
3.0 – 7.0 mm
(0.118 – 0.276 in)
(
−
1.8) – (+2.4) mm
[(
−
0.071) – (+0.094) in]
Rear bumper fascia – Rear fender
panel
–
0.1 – 1.0 mm
(0.004 – 0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
EXT-22
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Exploded View
INFOID:0000000010787440
Removal and Installation
INFOID:0000000010787441
REMOVAL
1.
Fully open hood assembly.
Turn fastener
Grommet
Front emblem
Front grille
Front camera (if equipped)
: Clip
: Pawl
JMKIB2961ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст