Nissan X-Trail 32. Manual — part 1241
FRONT GRILLE
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Remove front grille fixing clips
of front grille upper side.
3.
To disengage fasteners, locate the service holes top position of front grille. Insert a flat-bladed screwdriver
(A) into the service hole on vehicle left side and rotate turn fastener counterclockwise. Insert the flat-
bladed screwdriver into the service hole on vehicle right side and rotate turn fastener clockwise.
4.
Disengage front grille fixing clips and pawls from back side while
pulling front grille toward vehicle front.
5.
Disconnect front camera harness connector. (if equipped)
6.
Remove front grille.
7.
Remove the following parts after removing front grille.
• Front camera. Refer to
AV-269, "Removal and Installation"
• Front emblem.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing front grille, install turn fastener to back of front grille, and then install front grille.
: Vehicle front
JMKIB2845ZZ
JMKIB2846ZZ
: Clip
: Pawl
JMKIB2847ZZ
EXT-24
< REMOVAL AND INSTALLATION >
COWL TOP
COWL TOP
Exploded View
INFOID:0000000010787442
Cowl top seal
Cowl top cover
Cowl top grille clip
Cowl top cover cap
Cowl top extension
EPT seal [t: 10.0 mm (0.394 in)]
JMKIB2962ZZ
COWL TOP
EXT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000010787443
REMOVAL
1.
Remove front wiper arm (LH and RH). Refer to
WW-82, "WIPER ARM : Removal and Installation"
.
2.
Remove fender cover (LH and RH). Refer to
DLK-272, "FENDER COVER : Removal and Installation"
3.
Remove cowl top insulator fixing clips
, and then remove cowl
top insulator (R9M engine models only).
4.
Remove cowl top grille clip using a remover tool (A) according to
the numerical order 1
→
2 as shown by the arrows in the figure.
5.
Cover cowl top cover
and upper side of front fender panel
with a shop cloth (A) to prevent damage.
EPT seal [t: 3.0 mm (0.118 in)]
: Clip
: Pawl
: Vehicle front
: Always replace after every disassembly.
JMKIB3755ZZ
JMKIB2848ZZ
JMKIB2849ZZ
EXT-26
< REMOVAL AND INSTALLATION >
COWL TOP
6.
Disengage cowl top cover
using a remover tool (A) from wind-
shield glass lower molding
.
7.
Remove joint of front washer tube.
8.
Remove cowl top cover.
9.
Remove the following parts after removing cowl top cover.
• EPT seal.
• Cowl top seal.
• Cowl top cover cap.
• Front washer tube. Refer to
WW-101, "FRONT WASHER TUBE : Removal and Installation"
• Front washer nozzle. Refer to
WW-97, "FRONT WASHER NOZZLE : Removal and Installation"
10. Remove front wiper drive assembly. Refer to
WW-85, "WIPER DRIVE ASSEMBLY : Removal and Installa-
11. Remove cowl top extension mounting bolts and nut, and then remove cowl top extension.
12. Remove EPT seal after removing cowl top extension.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Clean the joint between the cowl top cover and the windshield, and then install them.
• Replace the EPT seal on the back surface with new EPT seal when reusing the cowl top cover.
• When installing cowl top cover
, always match perfectly the
portion
of cowl top extension
with the portion
of cowl
top cover.
: Windshield glass
JMKIB2850ZZ
JMKIB2851ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст