Nissan X-Trail 32. Manual — part 1612
MWI-130
< DTC/CIRCUIT DIAGNOSIS >
STEERING SWITCH SIGNAL A CIRCUIT
STEERING SWITCH SIGNAL A CIRCUIT
Component Function Check
INFOID:0000000010715017
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “STRG SW INPUT” monitor value.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
MWI-130, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010715018
1.
CHECK STEERING SWITCH SIGNAL A CIRCUIT
1.
Disconnect combination meter harness connector and spiral cable harness connector.
2.
Check continuity between combination meter harness connector and spiral cable harness connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT
1.
Check continuity between combination meter harness connector and spiral cable harness connector.
2.
Check continuity between combination meter harness connector and ground.
Condition
Value
BACK switch is pressed
SW1
MENU UP switch is pressed
SW2
MENU DOWN switch is pressed
SW3
TEL switch is pressed
SW4
ENTER switch is pressed
SW5
VOL DOWN switch is pressed
SW6
VOL UP switch is pressed
SW7
TEL END switch is pressed
SW8
SEEK DOWN switch is pressed
SW9
SEEK UP switch is pressed
SW10
Other than above
NO INPUT
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M34
22
M33
29
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
22
Not existed
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M34
21
M33
23
Existed
MWI
STEERING SWITCH SIGNAL A CIRCUIT
MWI-131
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SPIRAL CABLE
1.
Disconnect steering switch connector.
2.
Check continuity between spiral cable harness connectors.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace spiral cable. Refer to
SR-23, "Removal and Installation"
4.
CHECK STEERING SWITCH
Check steering switch. Refer to
MWI-131, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering wheel. Refer to
ST-12, "Removal and Installation"
Component Inspection
INFOID:0000000010715019
1.
CHECK STEERING SWITCH
1.
Remove steering switch. Refer to
MWI-154, "Removal and Installation"
2.
Measure the resistance between the steering switch connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering switch. Refer to
MWI-154, "Removal and Installation"
.
Combination meter
Ground
Continuity
Connector
Terminal
M34
21
Not existed
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M33
29
M303
10
Existed
23
4
Steering switch
Condition
Resistance
(Approx.)
Ω
Terminal
Terminal
10
4
ENTER switch is pressed
1982 – 2064
TEL switch is pressed
708 – 738
MENU DOWN switch is
pressed
314 – 328
MENU UP switch is pressed
118 – 124
BACK switch is pressed
0
5
SEEK UP switch is pressed
1982 – 2064
SEEK DOWN switch is
pressed
708 – 738
TEL END switch is pressed
314 – 328
VOL UP switch is pressed
118 – 124
VOL DOWN switch is
pressed
0
JSNIA7127GB
MWI-132
< DTC/CIRCUIT DIAGNOSIS >
STEERING SWITCH SIGNAL B CIRCUIT
STEERING SWITCH SIGNAL B CIRCUIT
Component Function Check
INFOID:0000000010715020
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “STRG SW INPUT” monitor value.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
MWI-130, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010715021
1.
CHECK STEERING SWITCH SIGNAL B CIRCUIT
1.
Disconnect combination meter harness connector and spiral cable harness connector.
2.
Check continuity between combination meter harness connector and spiral cable harness connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT
1.
Check continuity between combination meter harness connector and spiral cable harness connector.
2.
Check continuity between combination meter harness connector and ground.
Condition
Value
BACK switch is pressed
SW1
MENU UP switch is pressed
SW2
MENU DOWN switch is pressed
SW3
TEL switch is pressed
SW4
ENTER switch is pressed
SW5
VOL DOWN switch is pressed
SW6
VOL UP switch is pressed
SW7
TEL END switch is pressed
SW8
SEEK DOWN switch is pressed
SW9
SEEK UP switch is pressed
SW10
Other than above
NO INPUT
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M34
23
M33
24
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
23
Not existed
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M34
21
M33
23
Existed
MWI
STEERING SWITCH SIGNAL B CIRCUIT
MWI-133
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SPIRAL CABLE
1.
Disconnect steering switch connector.
2.
Check continuity between spiral cable harness connectors.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace spiral cable. Refer to
SR-23, "Removal and Installation"
4.
CHECK STEERING SWITCH
Check steering switch. Refer to
MWI-133, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering wheel. Refer to
ST-12, "Removal and Installation"
Component Inspection
INFOID:0000000010715022
1.
CHECK STEERING SWITCH
1.
Remove steering switch. Refer to
MWI-154, "Removal and Installation"
2.
Measure the resistance between the steering switch connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace steering switch. Refer to
MWI-154, "Removal and Installation"
.
Combination meter
Ground
Continuity
Connector
Terminal
M34
21
Not existed
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M33
24
M303
5
Existed
23
4
Steering switch
Condition
Resistance
(Approx.)
Ω
Terminal
Terminal
10
4
ENTER switch is pressed
1982 – 2064
TEL switch is pressed
708 – 738
MENU DOWN switch is
pressed
314 – 328
MENU UP switch is pressed
118 – 124
BACK switch is pressed
0
5
SEEK UP switch is pressed
1982 – 2064
SEEK DOWN switch is
pressed
708 – 738
TEL END switch is pressed
314 – 328
VOL UP switch is pressed
118 – 124
VOL DOWN switch is
pressed
0
JSNIA7127GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст