Nissan X-Trail 32. Manual — part 167
BRC-134
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C1116 STOP LAMP SWITCH
4.
Stop the vehicle.
5.
Vehicle stopped, and perform self-diagnosis for “ABS”.
Is DTC “C1116” detected?
YES
>>
Replace the ABS actuator and electric unit (control unit).
• LHD models: Refer to
BRC-217, "LHD : Removal and Installation"
• RHD models: Refer to
BRC-220, "RHD : Removal and Installation"
.
NO
>> Check pin terminals and connection of each harness connector for abnormal conditions. Repair or
replace error-detected parts.
C1118 4WD SYSTEM
BRC-135
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1118 4WD SYSTEM
DTC Description
INFOID:0000000010723679
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• 4WD control unit
• ABS actuator and electric unit (control unit)
FAIL-SAFE
The following functions are suspended.
• Advanced hill descent control function (Gasoline engine models)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ABS”.
Is DTC “C1118” detected?
YES
>> Proceed to
BRC-135, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010723680
1.
CHECK 4WD SYSTEM
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>>
Check the DTC.
• MR20DD engine and QR25DE engine models: Refer to
.
• R9M engine models: Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “ABS”.
2.
Turn the ignition switch OFF, and wait 10 seconds or more.
3.
Start the engine and drive the vehicle for a short period of time.
4.
Stop the vehicle.
5.
Vehicle stooped, and perform self-diagnosis for “ABS”.
Is DTC “C1118” detected?
YES
>>
Replace the ABS actuator and electric unit (control unit).
BRC-217, "LHD : Removal and Installation"
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1118
4WD SYSTEM
(4WD system)
When a malfunction is detected in 4WD system.
BRC-136
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C1118 4WD SYSTEM
• RHD models: Refer to
BRC-220, "RHD : Removal and Installation"
.
NO
>> Check pin terminals and connection of each harness connector for abnormal conditions. Repair or
replace error-detected parts.
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
BRC-137
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
DTC Description
INFOID:0000000010723681
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• ABS actuator and electric unit (control unit)
• Fusible link
• Battery power supply system
FAIL-SAFE
The following functions are suspended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential (BLSD) function
• Brake assist function
• Brake force distribution function
• hill start assist function
• Advanced hill descent control function (4WD models with gasoline engine)
• Active trace control function (control of chassis control module)
• Active ride control function (control of chassis control module)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ABS”.
Is any DTC “C1120”, “C1122”, “C1124”, “C1126” detected?
YES
>> Proceed to
BRC-137, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010723682
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1120
FR LH IN ABS SOL
(Front LH ABS IN solenoid valve)
When a malfunction is detected in front LH ABS IN valve.
C1122
FR RH IN ABS SOL
(Front RH ABS IN solenoid valve)
When a malfunction is detected in front RH ABS IN valve.
C1124
RR LH IN ABS SOL
(Rear LH ABS IN solenoid valve)
When a malfunction is detected in rear LH ABS IN valve.
C1126
RR RH IN ABS SOL
(Rear RH ABS IN solenoid valve)
When a malfunction is detected in rear RH ABS IN valve.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст