Nissan X-Trail 32. Manual — part 1599
MWI-78
< SYSTEM DESCRIPTION >
SYSTEM
• The combination meter displays level of ECO drive in conjunction with ECO pedal guide.
Average Fuel Consumption
The combination meter calculates average fuel consumption based on the following signals, and the calcu-
lated value is displayed on the information display.
NOTE:
• Average fuel consumption on the information display is updated approximately every 30 seconds.
Signal name
Signal path
Ignition signal
—
ECO pedal guide signal
ECM
Combination
meter
JSNIA5881GB
Signal name
Signal source
Ignition signal
—
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Steering switch signal
Steering switch
Combination meter
MWI
SYSTEM
MWI-79
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “
−−−
”
is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).
Average Vehicle Speed
The combination meter calculates average vehicle speed based on the following signals, and the calculated
value is displayed on the information display.
NOTE:
• Average fuel consumption on the information display is updated approximately every 30 seconds.
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “
−−−
”
is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).
Distance to Empty
The combination meter calculates distance to empty based on the following signals, and the calculated value
is displayed on the information display.
NOTE:
• Distance to empty on the information display is updated approximately every 30 seconds.
• When the ignition switch is turned ON right after battery removal and installation, “
−−−
” is displayed until after
a travel of 30 seconds.
• The indicated values may not match each other when refueling with the ignition switch ON.
Travel Time
The combination meter measures and displays travel time (ignition switch ON time).
ECO Drive Report
• The ECO drive report is a function which displays
ECO evalua-
tion,
the last five data of average fuel consumption,
present
fuel economy (present value), and
the best fuel economy (high-
est value) on the information display by calculating and recording
average fuel consumption.
• The combination meter calculates the average fuel consumption according to the signal below, detects the
status of ECO mode , and displays “ECO drive report” on the information display when the ignition switch is
turned ON
→
OFF.
NOTE:
Signal name
Signal source
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Steering switch signal
Steering switch
Combination meter
Signal name
Signal source
Ignition signal
—
Fuel level sensor signal
Fuel level sensor unit
Combination meter
Fuel consumption monitor signal
ECM
Combination meter
Shift position signal
TCM
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
JSNIA7201ZZ
MWI-80
< SYSTEM DESCRIPTION >
SYSTEM
ECO evaluation is displayed only when travelling ten minutes or more in ECO mode.
Stop/Start System Information
• Stop/Start system information displays the time elapsed and the amount of CO2 reduced during idling stop.
• Two types of mode can be displayed in stop/start system information as follows:
- Accumulated idling stop time and CO2 reduction amount which are unable to be reset.
- Accumulated idling stop time and amount of CO2 reduced during the time until the user resets them arbi-
trarily.
• The combination meter calculates the time elapsed and amount of CO2 reduced during idling stop according
to the signals listed below and displays “Idling Stop Information” on the information display.
AMBIENT TEMPERATURE
The combination meter calculates ambient temperature based on the following signals, and the calculated
value is displayed on the information display.
NOTE:
• The indicated temperature is corrected based on an ignition signal, ambient temperature detected by the
ambient sensor, and vehicle speed signal. The indicated temperature is not raised under vehicle speed less
than 20 km/h (12 MPH).
• The ambient sensor input value that is displayed on “Data Monitor” of CONSULT is the value before the cor-
rection. It may not match the indicated temperature on the information display.
• Depending on engine heat or heat on the road surfaces, an ambient temperature may be indicated higher
than actual one.
METER ILLUMINATION LEVEL
The combination meter displays the illuminance level of the back light on the information display by turning the
illumination control switch.
Refer to
MWI-68, "METER ILLUMINATION CONTROL : System Description"
CLOCK
The combination meter displays “Clock” on the information display according to the following signals.
Signal name
Signal path
Ignition signal
—
Fuel consumption monitor
signal
ECM
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
ECO mode indicator signal
ECM
Combination meter
Signal name
Signal path
Ignition signal
—
Stop/start status signal
ECM
Combination meter
Stop/start permit signal
ECM
Combination meter
Engine speed signal
TCM
Combination meter
Signal name
Signal path
Ignition signal
—
Ambient sensor signal
Ambient sensor
Combination meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
MWI
SYSTEM
MWI-81
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
• For models without navigation system, the combination meter calculates time and displays it on the informa-
tion display.
• The settings screen of the information display allows the selection of time indication between 12-hour and
24-hour formats.
Signal name
Signal path
Ignition signal
—
Clock signal
Without naviga-
tion
Audio unit
Combination meter
With navigation
NAVI control unit
Combination meter
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст