Nissan X-Trail 32. Manual — part 1333
GW-50
< REMOVAL AND INSTALLATION >
FRONT DOOR REGULATOR
• Work procedure. Refer to
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
REAR DOOR GLASS
GW-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000010755116
RHD models
REAR DOOR GLASS
REAR DOOR GLASS : Removal and Installation
INFOID:0000000010755117
REMOVAL
CAUTION:
Never damage rear door glass and rear door panel.
1.
Remove rear door corner piece. Refer to
GW-54, "REAR DOOR CORNER PIECE : Removal and Installa-
JMKIB3200GB
Rear door glass run
Rear door panel
Rear door sealing screen
Rear door regulator
Rear door power window motor
Rear door glass
Rear door lower sash
Rear door corner piece
: N·m (kg-m, in-lb)
,
,
,
,
,
,
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
GW-52
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
2.
Operate power window switch to raise or lower rear door glass until rear door glass mounting bolts
can
be seen, and then remove rear door glass mounting bolts.
3.
Hold securely rear door glass and pull it out of rear door panel to
remove rear door glass.
CAUTION:
Never damage rear door glass and rear door panel.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Tighten rear door glass mounting bolts to the specified torque. Refer to
.
REAR DOOR LOWER SASH
REAR DOOR LOWER SASH : Removal and Installation
INFOID:0000000010755118
REMOVAL
CAUTION:
Never damage rear door glass and rear door panel.
1.
Fully open rear door glass.
2.
Remove rear door inside handle. Refer to the following.
• Type 1: Refer to
DLK-309, "INSIDE HANDLE : Removal and Installation"
• Type 2: Refer to
DLK-616, "INSIDE HANDLE : Removal and Installation"
• Type 3: Refer to
DLK-779, "INSIDE HANDLE : Removal and Installation"
• Type 4: Refer to
DLK-921, "INSIDE HANDLE : Removal and Installation"
3.
Disconnect rear door speaker harness connector
.
JMKIB3150ZZ
JMKIB3173ZZ
JMKIB3147ZZ
REAR DOOR GLASS
GW-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
4.
Cut butyl-tape inside of rear door sealing screen by using cutter knife (A).
CAUTION:
Cut the butyl-tape so that remain on rear door sealing screen, if the rear door sealing screen is
reused.
5.
Reconnect power window switch.
6.
Fully close rear door glass.
7.
Disengage rear door glass run
from rear door lower sash
.
8.
Remove rear door lower sash mounting bolts
.
JMKIB3148ZZ
JMKIB3149ZZ
JMKIB3164ZZ
JMKIB3165ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст