Nissan X-Trail 32. Manual — part 108
BR-26
< REMOVAL AND INSTALLATION >
[LHD]
BRAKE PIPING
4.
Remove the union bolt
and copper washers
, and remove
the brake hose
from the brake caliper assembly.
5.
Remove the lock plate
and remove the brake hose.
INSTALLATION
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied
with, brake fluid may splash.
• Never allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
1.
Assemble the union bolt
and the copper washer
to the
brake hose.
CAUTION:
Never reuse the copper washer.
2.
Align the brake hose pin
with the brake caliper assembly pro-
jection
, and tighten the union bolt to the specified torque.
3.
Install the brake tube
to the brake hose
, temporarily tighten
the flare nut
by hand until it does not rotate further, and fix the
brake hose to the bracket
with the lock plate
.
CAUTION:
Check that all brake hoses and brake tubes are not twisted
and bent.
4.
Tighten the flare nut to the specified torque with a flare nut
torque wrench (A).
CAUTION:
Never scratch the flare nut and the brake tube.
5.
Refill with new brake fluid and perform the air bleeding. Refer to
BR-14, "Bleeding Brake System"
CAUTION:
Never reuse drained brake fluid.
6.
Install tires. Refer to
WT-61, "Removal and Installation"
7.
Perform inspection after installation. Refer to
.
JPFIA0819ZZ
JPFIA0820ZZ
JPFIA0821ZZ
JPFIA0061ZZ
BRAKE PIPING
BR-27
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT : Inspection
INFOID:0000000010838513
INSPECTION AFTER INSTALLATION
1.
Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interfer-
ence with other components when steering the steering wheel; no looseness at connections.
CAUTION:
Clearance with brake hose and each parts being secured more than 10 mm (0.39 in) in unladen
condition
*
.
*: Fuel, engine coolant and lubricant are quantity to specified. Spare tire, jack, hand tools and mats
are brought out of vehicle.
2.
Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately
5 seconds with the engine running. Check for any fluid leakage.
CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged,
worn or deformed) part if any brake fluid leakage is present.
REAR
REAR : Exploded View
INFOID:0000000010838514
MR20DD
Brake tube
Lock plate
Brake hose
Union bolt
Copper washer
Brake tube bracket
Brake tube bracket
Brake tube bracket
To connector
To rear brake hose
Floor side
Caliper side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA2655GB
BR-28
< REMOVAL AND INSTALLATION >
[LHD]
BRAKE PIPING
EXCEPT MR20DD
Brake tube
Lock plate
Brake hose
Union bolt
Copper washer
Brake tube bracket
Brake tube bracket
To connector
To rear brake hose
Floor side
Caliper side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA2656GB
BRAKE PIPING
BR-29
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR : Hydraulic Piping
INFOID:0000000010838515
REAR : Removal and Installation
INFOID:0000000010838516
REMOVAL
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied
with, brake fluid may splash.
• Wipe off immediately when attaching brake fluid with disc rotor and caliper assembly.
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Drain brake fluid. Refer to
3.
Loosen the flare nut
with a flare nut wrench (A) and separate
the brake tube
from the hose
.
CAUTION:
• Never scratch the flare nut and the brake tube.
• Never bend sharply, twist or strongly pull out the brake
hoses and tubes.
• Cover open end of brake tubes and hoses when discon-
necting to prevent entrance of dirt.
4.
Disconnect the lock plate
, then remove the brake hose.
ABS actuator and electric unit (con-
trol unit)
Front disc brake
Master cylinder assembly
Brake booster
Connector
Rear disc brake
Brake tube
Brake hose
: Flare nut
: Union bolt
JSFIA2379ZZ
JSFIA1064ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст