Nissan X-Trail 32. Manual — part 107
BR-22
< REMOVAL AND INSTALLATION >
[LHD]
BRAKE PEDAL
4.
Disconnect the accelerator pedal harness connector.
5.
Remove snap pin
and clevis pin
from clevis of brake
booster .
6.
Remove the brake pedal assembly.
CAUTION:
Hold the brake booster and master cylinder assembly so as not to drop out or contact them other
parts.
7.
Remove the accelerator pedal from the brake pedal assembly. Refer to
8.
Perform inspection after removal. Refer to
BR-22, "Inspection and Adjustment"
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never reuse the clevis pin and snap pin.
• Apply the multi-purpose grease to the clevis pin and the mating faces. (Not necessary if grease has been
already applied)
NOTE:
The clevis pin may be inserted in either direction.
• Never impact brake pedal such as drop and interference with tools and parts.
• Replace brake pedal when impacting brake pedal.
• Perform adjustment after installation. Refer to
BR-22, "Inspection and Adjustment"
.
Inspection and Adjustment
INFOID:0000000010838509
INSPECTION AFTER REMOVAL
Check for the following items and replace the brake pedal assembly if necessary.
• Check rivet
for deformation, crack, and damage.
• Check the brake pedal for bend, damage, and cracks on the
welded parts.
CAUTION:
Never loose bolt
.
JPFIA0816ZZ
JSFIA2250ZZ
BRAKE PEDAL
BR-23
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Check clevis pin and plastic stopper
for damage and deforma-
tion. Replace clevis pin if necessary.
ADJUSTMENT AFTER INSTALLATION
• Adjust each item of brake pedal after installing the brake pedal assembly to the vehicle. Refer to
.
• Perform the release position learning of the accelerator pedal.
- MR20DD: Refer to
- QR25DE: Refer to
- R9M: Refer to
.
PFIA0756J
BR-24
< REMOVAL AND INSTALLATION >
[LHD]
BRAKE PIPING
BRAKE PIPING
FRONT
FRONT : Exploded View
INFOID:0000000010838510
Brake tube
ABS actuator and electric unit (con-
trol unit)
Connector bracket
Connector
Brake booster
Master cylinder assembly
Brake tube bracket
Lock plate
Brake hose
Union bolt
Copper washer
To rear brake tube
: Indicates that the part is connected at points with same symbol in actual vehicle.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA2537GB
BRAKE PIPING
BR-25
< REMOVAL AND INSTALLATION >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT : Hydraulic Piping
INFOID:0000000010838511
FRONT : Removal and Installation
INFOID:0000000010838512
REMOVAL
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface. For brake component parts,
never wash them with water.
• Never depress the brake pedal while removing the brake hose or brake tube. If this is not complied
with, brake fluid may splash.
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Drain brake fluid. Refer to
3.
Loosen the flare nut
with a flare nut wrench (A) and separate
the brake tube
from the brake hose
.
CAUTION:
• Never scratch the flare nut and the brake tube.
• Never bend sharply, twist or strongly pull out the brake
hoses and tubes.
• Cover open end of brake tubes and hoses when discon-
necting to prevent entrance of dirt.
ABS actuator and electric unit (con-
trol unit)
Front disc brake
Master cylinder assembly
Brake booster
Connector
Rear disc brake
Brake tube
Brake hose
: Flare nut
: Union bolt
JSFIA2379ZZ
JPFIA0847ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст