Nissan X-Trail 32. Manual — part 1567
MA-58
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
1.
Remove plug
.
2.
Measure the oil level (L) using a suitable gauge (A) as shown in
the figure and check if it is within the specifications.
CAUTION:
• Turn the ignition switch OFF while checking oil level.
• Attach the suitable gauge to the wall of the plug mounting
hole for accurate measurement.
3.
Set O-ring on plug and install it to transaxle assembly.
CAUTION:
Never reuse O-ring.
4.
Tighten plug mounting bolt to the specified torque. Refer to
M/T OIL [RS6F52A (2WD)] : Draining
INFOID:0000000011004116
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug
and gasket, then drain gear
oil.
3.
Set a gasket on drain plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
M/T OIL [RS6F52A (2WD)] : Refilling
INFOID:0000000011004117
1.
Remove plug
.
2.
Fill with new gear oil.
NOTE:
Oil capacity is reference. Because oil level is controlled by oil
surface position.
3.
After refilling gear oil, check the oil level. Refer to
4.
Set O-ring on plug and install it to transaxle assembly.
CAUTION:
Never reuse O-ring.
5.
Tighten plug mounting bolt to the specified torque. Refer to
M/T OIL [RS6F52A (4WD)]
M/T OIL [RS6F52A (4WD)] : Inspection
INFOID:0000000011004118
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
Oil level
: Refer to
JPDIC0138ZZ
JSDIA6146ZZ
Recommended oil and
capacity (reference)
: Refer to
.
JSDIA6147ZZ
CHASSIS MAINTENANCE
MA-59
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Remove filler plug
.
2.
Measure the oil level (L) using a suitable gauge (A) as shown in
the figure and check if it is within the specifications.
CAUTION:
• Turn the ignition switch OFF while checking oil level.
• Attach the suitable gauge to the wall of the plug mounting
hole for accurate measurement.
3.
Set gasket on filler plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
.
M/T OIL [RS6F52A (4WD)] : Draining
INFOID:0000000011004119
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug
and gasket, then drain gear
oil.
3.
Set a gasket on drain plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
M/T OIL [RS6F52A (4WD)] : Refilling
INFOID:0000000011004120
1.
Remove filler plug
.
2.
Fill with new gear oil.
NOTE:
Oil capacity is reference. Because oil level is controlled by oil
surface position.
3.
After refilling gear oil, check the oil level. Refer to
4.
Set gasket on filler plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
5.
Tighten filler plug to the specified torque. Refer to
.
CLUTCH FLUID
CLUTCH FLUID : Inspection
INFOID:0000000010828062
FLUID LEAKAGE
• Check clutch line for cracks, deterioration or other damage. Replace any damaged parts.
• Check for fluid leakage by fully depressing clutch pedal while engine is running.
CAUTION:
: Vehicle front
Oil level
: Refer to
JPDIC0139ZZ
JSDIA6154ZZ
Recommended oil and
capacity (reference)
: Refer to
.
JSDIA6155ZZ
MA-60
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
If leakage occurs around joints, reinstall the joints or, if necessary, replace damaged parts.
FLUID LEVEL
• Check that the fluid level in the reservoir tank is within the specified
range (MAX – MIN lines).
• Visually check for any clutch fluid leakage around the reservoir
tank.
• Check the clutch system for any leakage if the fluid level is
extremely low (lower than MIN).
TRANSFER OIL [TY21C (MR20DD)]
TRANSFER OIL [TY21C (MR20DD)] : Inspection
INFOID:0000000011008824
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug
and gasket. Then check that oil is filled up
from mounting hole for filler plug.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add transfer oil if necessary. Refer to
2.
Set a new gasket on filler plug and install it on transfer assem-
bly. Refer to
.
CAUTION:
Never reuse gasket.
TRANSFER OIL [TY21C (MR20DD)] : Draining
INFOID:0000000011008825
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Turn the ignition switch OFF.
3.
Remove drain plug
and gasket.
4.
Drain transfer oil.
5.
Before installing drain plug, set a new gasket. Install drain plug
to transfer assembly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
SFIA2634J
JSDIA5349ZZ
JSDIA5350ZZ
CHASSIS MAINTENANCE
MA-61
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
TRANSFER OIL [TY21C (MR20DD)] : Refilling
INFOID:0000000011008826
1.
Remove filler plug
and gasket. Then fill with new transfer oil
until oil level reaches the specified level near filler plug mounting
hole.
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug to
transfer assembly and tighten to the specified torque. Refer to
.
CAUTION:
Never reuse gasket.
TRANSFER OIL [TY21C (QR25DE)]
TRANSFER OIL [TY21C (QR25DE)] : Inspection
INFOID:0000000011008827
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug
and gasket. Then check that oil is filled up
from mounting hole for filler plug.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add transfer oil if necessary. Refer to
2.
Set a new gasket on filler plug and install it on transfer assem-
bly. Refer to
.
CAUTION:
Never reuse gasket.
TRANSFER OIL [TY21C (QR25DE)] : Draining
INFOID:0000000011008828
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Turn the ignition switch OFF.
3.
Remove drain plug
and gasket.
4.
Drain transfer oil.
5.
Before installing drain plug, set a new gasket. Install drain plug
to transfer assembly and tighten to the specified torque. Refer to
.
CAUTION:
Never reuse gasket.
Recommended
oil and capacity
.
JSDIA5349ZZ
: Oil level
: Vehicle front
ALDIA0503ZZ
: Vehicle front
AWDIA1153ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст