Nissan X-Trail 32. Manual — part 1568
MA-62
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
TRANSFER OIL [TY21C (QR25DE)] : Refilling
INFOID:0000000011008829
1.
Remove filler plug
and gasket. Then fill with new transfer oil
until oil level reaches the specified level near filler plug mounting
hole.
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug to transfer assembly and tighten to the spec-
ified torque. Refer to
.
CAUTION:
Never reuse gasket.
TRANSFER OIL (TY30A)
TRANSFER OIL (TY30A) : Inspection
INFOID:0000000011008830
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for oil leakage.
OIL LEVEL
1.
Check oil level from filler plug mounting hole as shown in the fig-
ure, after removing filler plug
and gasket from transfer assem-
bly.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add transfer oil if necessary. Refer to
.
2.
Set a gasket on filler plug and install it on transfer assembly.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
TRANSFER OIL (TY30A) : Draining
INFOID:0000000011008831
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the vehicle and turn the ignition switch OFF.
3.
Remove drain plug
and gasket.
CAUTION:
Never remove plug
for tooth contact test.
4.
Drain transfer oil.
5.
Set a gasket on drain plug and install it to transfer assembly.
CAUTION:
Never reuse gasket.
6.
Tighten drain plug to the specified torque. Refer to
: Oil level
: Vehicle front
Recommended
oil and capacity
: Refer to
.
ALDIA0503ZZ
JSDIA6402ZZ
JSDIA6403ZZ
CHASSIS MAINTENANCE
MA-63
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
TRANSFER OIL (TY30A) : Refilling
INFOID:0000000011008832
1.
Fill with new transfer oil until oil level reaches the specified level
near filler plug mounting hole, after removing filler plug
and
gasket from transfer assembly.
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Set a gasket on filler plug, and install it to transfer assembly.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
REAR PROPELLER SHAFT
REAR PROPELLER SHAFT : Inspection
INFOID:0000000010828070
LOOSENESS OF CONNECTED PART
Check each fixing bolt and nut for looseness using torque wrench. For each tightening torque, refer to
BACKLASH OF JOINT PART
Move the joint of propeller shaft up and down and from side to side
(axial direction of shaft and right angle to shaft) to check that the joint
has no backlash. If the joint has a malfunction, remove propeller
shaft and perform inspection.
BACKLASH OF CENTER BEARING
Move the shaft near center bearing up and down and from side to
side (axial direction of shaft and right angle to shaft) to check that the
bearing has no backlash. If the bearing has a malfunction, remove
propeller shaft and perform inspection.
APPEARANCE AND NOISE
• Check the propeller shaft tube surface for dents or cracks. If malfunction is detected, replace propeller shaft
assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, adjust the propeller shaft phase first.
1.
Check the propeller shaft for bend and damage. If damaged, replace propeller shaft assembly.
Recommended
oil and capacity
.
JSDIA6429ZZ
MAA0555D
MAA0005D
MA-64
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
2.
Perform a cruise test drive to check the propeller shaft for runout. If vibration occurs, separate propeller
shaft at final drive companion flange; then change the phase between electric controlled coupling stud bolt
and propeller shaft by the one bolt hole at a time and install propeller shaft.
3.
If vibration is still detected, measure propeller shaft runout after removing it. Refer to
REAR DIFFERENTIAL GEAR OIL
REAR DIFFERENTIAL GEAR OIL : Inspection
INFOID:0000000011008833
OIL LEAKAGE
Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
1.
Check oil level from filler plug mounting hole as shown in the fig-
ure after removing filler plug
and gasket from final drive
assembly.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add gear oil if necessary. Refer to
.
2.
Set a gasket on filler plug and install it on final drive assembly.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
REAR DIFFERENTIAL GEAR OIL : Draining
INFOID:0000000011008834
1.
Turn the ignition switch OFF.
2.
Remove drain plug
and gasket.
3.
Drain gear oil.
4.
Set a gasket on drain plug and install it to final drive assembly.
CAUTION:
Never reuse gasket.
5.
Tighten drain plug to the specified torque. Refer to
REAR DIFFERENTIAL GEAR OIL : Refilling
INFOID:0000000011008835
1.
Remove filler plug
and gasket. Then fill with new gear oil until
oil level reaches the specified level near filler plug mounting
hole.
2.
Set a gasket on filler plug, and install it to final drive assembly.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
WHEELS
JPDID0164ZZ
JPDID0163ZZ
Recommended
oil and capacity
: Refer to
.
JPDID0164ZZ
CHASSIS MAINTENANCE
MA-65
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
WHEELS : Wheel Balance Adjustment (Aluminum Wheel)
INFOID:0000000010828074
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Never scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Never install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, always to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) bal-
ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
• When installing balance weight
to road wheels, set it into
the grooved area
on the inner wall of the road wheel as
shown in the figure so that the balance weight center
is
aligned with the tire balance machine indication position
(angle) .
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Never install three or more sheets of balance weight.
SMA054D
JPEIC0040ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст