Nissan X-Trail 32. Manual — part 2091
TM-322
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0705 TRANSMISSION RANGE SENSOR A
P0705 TRANSMISSION RANGE SENSOR A
DTC Description
INFOID:0000000010622512
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Short circuit between transmission range switch and TCM)
• Transmission range switch
FAIL-SAFE
• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1.
Turn ignition switch ON.
2.
Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
5 seconds or more.)
3.
Check the first trip DTC.
Is “P0705” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622513
1.
CHECK TCM INPUT SIGNALS
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Data Monitor” in “TRANSMISSION”.
3.
Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, and “P POSITION SW”.
4.
Shift the selector lever through entire positions from “P” to “D” and check ON/OFF of each monitor item.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0705
T/M RANGE SENSOR A
[Transmission Range Sensor A Circuit (PRNDL
Input)]
When all of the following conditions are satisfied and this state is main-
tained for 2 seconds:
• Two or more range signals simultaneously stay ON continuously
• TCM power supply voltage: More than 11 V
Monitor item
Condition
Condition
D POSITION SW
Selector lever: “D” position
On
Other than the above
Off
N POSITION SW
Selector lever: “N” position
On
Other than the above
Off
P0705 TRANSMISSION RANGE SENSOR A
TM-323
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Without CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Turn ignition switch ON.
4.
Shift the selector lever from “P” to “D” and check voltage between TCM harness connector terminals and
ground.
Is the inspection result normal?
YES >> INSPECTION
END
NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.
2.
CHECK D POSITION SW CIRCUIT (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK D POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
R POSITION SW
Selector lever: “R” position
On
Other than the above
Off
P POSITION SW
Selector lever: “P” position
On
Other than the above
Off
+
−
Condition
Voltage
TCM
Connector
Terminal
F23
4
Ground
Selector lever: “D” position
10 – 16 V
Other than the above
Approx. 0 V
5
Selector lever: “N” position
10 – 16 V
Other than the above
Approx. 0 V
6
Selector lever: “R” position
10 – 16 V
Other than the above
Approx. 0 V
7
Selector lever: “P” position
10 – 16 V
Other than the above
Approx. 0 V
Monitor item
Condition
Condition
TCM
Continuity
Connector
Terminal
F23
4
2
Not existed
5
6
7
TM-324
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0705 TRANSMISSION RANGE SENSOR A
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK N POSITION SW CIRCUIT (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK N POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK P POSITION SW CIRCUIT (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F23
4
Ground
0 V
TCM
Continuity
Connector
Terminal
F23
5
2
Not existed
4
6
7
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F23
5
Ground
0 V
TCM
Continuity
Connector
Terminal
F23
7
2
Not existed
4
5
6
P0705 TRANSMISSION RANGE SENSOR A
TM-325
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK P POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
8.
CHECK R POSITION SW CIRCUIT (PART1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning parts.
9.
CHECK R POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
10.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-325, "Component Inspection"
Is the check result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000010622514
1.
CHECK TRANSMISSION RANGE SWITCH
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F23
7
Ground
0 V
TCM
Continuity
Connector
Terminal
F23
6
2
Not existed
4
5
7
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F23
6
Ground
0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст