Nissan X-Trail 32. Manual — part 2092
TM-326
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0705 TRANSMISSION RANGE SENSOR A
Check continuity between transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
450, "Removal and Installation"
.
Transmission range switch
Condition
Continuity
Terminal
1 – 2
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
3 – 4
Manual lever: “P” position
Existed
Other than the above
Not existed
3 – 5
Manual lever: “R” position
Existed
Other than the above
Not existed
3 – 6
Manual lever: “N position
Existed
Other than the above
Not existed
3 – 7
Manual lever: “D” position
Existed
Other than the above
Not existed
P0706 TRANSMISSION RANGE SENSOR A
TM-327
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0706 TRANSMISSION RANGE SENSOR A
DTC Description
INFOID:0000000010622515
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit
between transmission range switch and TCM)
• Transmission range switch
• Control cable
Harness or connector (CAN communication line is error)
FAIL-SAFE
• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
40 seconds or more.)
3.
Check the first trip DTC.
Is “P0706” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622516
1.
ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Results” in “TRANSMISSION”.
3.
Touch “Erase”.
4.
Perform “DTC CONFIRMATION PROCEDURE". Refer to
.
Is “P0706” detected?
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0706
T/M RANGE SENSOR A
(Transmission Range Sensor A Circuit Range/
Performance)
When all of the following conditions are satisfied and this state is main-
tained for 30 seconds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V
TM-328
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0706 TRANSMISSION RANGE SENSOR A
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between transmission range switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 7.
4.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between transmission range switch harness connector terminals and TCM harness con-
nector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2)
Check continuity between transmission range switch harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-329, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
7.
CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH
+
−
Voltage
Transmission range switch
Connector
Terminal
F22
3
Ground
10 – 16 V
Transmission range switch
TCM
Continuity
Connector
Terminal
Connector
Terminal
F22
4
F23
7
Existed
5
6
6
5
7
4
Transmission range switch
—
Continuity
Connector
Terminal
F22
4
Ground
Not existed
5
6
7
P0706 TRANSMISSION RANGE SENSOR A
TM-329
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector terminal and transmission range switch harness
connector terminal.
Is the check result normal?
YES
>> GO TO 8.
NO
>> Repair or replace malfunctioning parts.
8.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram - IGNITION POWER SUPPLY -"
.
• Short circuit in harness between IPDM E/R harness connector terminal 71 and transmission range switch
harness connector terminal 3.
• 10A fuse (No. 97, located in the IPDM E/R). Refer to
PG-89, "Fuse, Connector and Terminal Arrangement"
• IPDM E/R
Is the check result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000010622517
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
450, "Removal and Installation"
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F72
71
F22
3
Existed
Transmission range switch
Condition
Continuity
Terminal
1 – 2
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
3 – 4
Manual lever: “P” position
Existed
Other than the above
Not existed
3 – 5
Manual lever: “R” position
Existed
Other than the above
Not existed
3 – 6
Manual lever: “N position
Existed
Other than the above
Not existed
3 – 7
Manual lever: “D” position
Existed
Other than the above
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст