Nissan X-Trail 32. Manual — part 1270
FAX-72
< REMOVAL AND INSTALLATION >
[4WD]
FRONT WHEEL HUB AND KNUCKLE
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000010824407
Removal and Installation
INFOID:0000000010824408
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove front wheel sensor from steering kunckle. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
Steering knuckle
Splash guard
Hub bolt
Wheel hub and bearing assembly
Disc rotor
Wheel hub lock nut
Adjusting cap
Cotter pin
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JMDIA1520GB
JSDIA3795ZZ
FRONT WHEEL HUB AND KNUCKLE
FAX-73
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor.
CAUTION:
• Put matching marks
on the wheel hub and bearing
assembly and the disc rotor before removing the disc
rotor.
• Never drop disc rotor.
6.
Remove cotter pin, adjusting cap and then loosen wheel hub
lock nut, using a hub lock nut wrench (A) (SST: KV40104000).
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
8.
Remove wheel hub lock nut.
9.
Remove wheel hub and bearing assembly.
10. Remove splash guard.
11. Remove transverse link from steering knuckle and front suspension member. Refer to
12. Separate steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
.
13. Separate the connection of strut assembly and steering knuckle as follows.
CAUTION:
JPDIG0066ZZ
JSDIA2708ZZ
JPDIG0070ZZ
FAX-74
< REMOVAL AND INSTALLATION >
[4WD]
FRONT WHEEL HUB AND KNUCKLE
Be sure to keep the following procedure because steering knuckle may be damaged when you
enlarge the gap of steering knuckle too much.
a.
Remove strut mounting bolts from steering knuckle.
b.
Measure the gap (A) of the steering knuckle. And then mark the
enlarged limit (B) to the chisel.
NOTE:
Standard of gap: 6.9
±
0.5 mm (2.56
±
0.02 in)
c.
Enlarge the gap of the steering knuckle with the chisel (A) (com-
mercial service tool) not to surpass a limit as shown in the figure.
CAUTION:
• Never enlarge the gap more than 2.5mm (0.098in).
• Be careful not to damage the projection
and strut
assembly
with the chisel.
•
d.
Separate the connection of strut assembly and steering knuckle.
CAUTION:
• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
• Be sure to remove lubricants if lubricant has been used to separate the connection of strut
assembly and steering knuckle.
Marking
Enlarged limit (B) = gap (A) + 2.5 mm (0.098 in)
JSEIA0916ZZ
JSEIA0917ZZ
JMEIA0227ZZ
FRONT WHEEL HUB AND KNUCKLE
FAX-75
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
14. Remove hub bolts
from wheel hub and bearing assembly,
using the ball joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub and bearing assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub and bearing assembly.
15. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
Hub Bolts
• Place a washer
as shown in the figure to install the hub bolts
by using the tightening force of the nut
.
CAUTION:
• Check that there is no clearance between wheel hub and
bearing assembly, and hub bolt.
• Never reuse hub bolt.
Drive shaft
• Clean the matching surface of wheel hub lock nut and wheel hub and bearing assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub and bear-
ing assembly. And then apply paste [service parts (440037S000)]
to surface
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
• Tighten the wheel hub lock nut to the specified torque. Refer to
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
JPDIF0299ZZ
JPDIF0300ZZ
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIG0122ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст