Nissan X-Trail 32. Manual — part 1269
FAX-68
< PREPARATION >
[4WD]
PREPARATION
Lubricant or/and Sealant
INFOID:0000000010824403
Sliding hammer
Removing drive shaft
Ball joint remover
Removing hub bolt
Chisel
Removing and installing steering knuckle and
strut assembly
A: 16 – 32 mm (0.63 – 1.26 in)
B: 10 mm (0.39 in) or more
C: 40 – 70 mm (1.57 – 2.76 in)
L: 220 mm (7.87 in) or less
S: 14 mm (0.55 in) or more
ZZA0023D
NT146
JSEIA0915ZZ
Name
Description
Fill NISSAN Genuine grease or equivalent
• Joint sub-assembly inside
• Housing inside
Apply paste [service parts (440037S000)]
• Joint sub-assembly
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
FAX-69
< SYMPTOM DIAGNOSIS >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010824404
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
,
—
—
NV
H in
F
A
X
an
d
FSU s
e
c
tio
ns
Re
fe
r to
FRONT AXL
E i
n
t
h
is cha
rt
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
NVH in S
T
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e joi
n
t an
gl
e
Jo
in
t sl
id
in
g
re
si
st
a
n
c
e
Im
ba
la
nc
e
Im
p
rop
er i
n
s
ta
lla
ti
o
n
, lo
os
en
es
s
Part
s interf
erence
Whe
e
l be
ari
n
g
da
ma
ge
FRONT A
X
LE
AND FRONT SUSP
ENSION
FRONT A
X
LE
TI
RE
ROAD WHEE
L
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
FRONT
AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
FAX-70
< PERIODIC MAINTENANCE >
[4WD]
FRONT WHEEL HUB AND KNUCKLE
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000010824405
COMPONENT PART
Make sure that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part if necessary.
• Move wheel hub and bearing assembly in the axial direction by hand. Check there is no looseness of wheel
bearing.
• Rotate wheel hub and make sure there is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing assembly.
Axial end play
: Refer to
FRONT DRIVE SHAFT
FAX-71
< PERIODIC MAINTENANCE >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Inspection
INFOID:0000000010824406
FRONT DRIVE SHAFT INSPECTION
Check the following items, and replace the part if necessary.
• Check drive shaft mounting point and joint for looseness and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occur from drive shaft.
• Check boot for cracks and other damage.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст