Nissan X-Trail 32. Manual — part 1279
FAX-108
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
1.
Remove dust shield from housing.
2.
Remove snap ring
.
3.
Press out support bearing from housing.
4.
Remove dust shield.
Dynamic Damper
Remove damper bands, then remove dynamic damper from shaft.
Wheel Side
1.
Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Remove boot bands, and then remove boot from joint sub-assembly.
3.
Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
• Align sliding hammer and drive shaft and remove them by
pulling directory.
4.
Remove circular clip from shaft.
5.
Remove boot from shaft.
6.
Clean old grease on joint sub-assembly with paper towels while rotating ball cage.
ASSEMBLY
JPDIF0121ZZ
JPDIF0106ZZ
YAX004
JPDIG0151ZZ
FRONT DRIVE SHAFT
FAX-109
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Transaxle Assembly Side
1.
Wrap serration on shaft with tape
to protect boot from dam-
age. Install new boot and boot bands to shaft.
CAUTION:
Never reuse boot and boot band.
2.
Remove the tape wrapped around the serration on shaft.
3.
To install the spider assembly
, align it with the matching
marks
on the shaft
put during the removal, and direct the
serration mounting surface
to the shaft.
4.
Secure spider assembly onto shaft with snap ring
.
CAUTION:
Never reuse snap ring.
5.
Apply the appropriate amount of grease to spider assembly and
sliding surface.
6.
Assemble the housing onto spider assembly, and apply the bal-
ance of the specified amount grease.
7.
Align matching marks put during the removal of housing.
8.
Install stopper ring.
CAUTION:
Never reuse stopper ring.
9.
Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on shaft or housing, boot may be removed.
Remove all grease from the surface.
10. To prevent from deformation of the boot, adjust the boot installa-
tion length to the value shown below (L) by inserting the suitable
tool into the inside of boot from the large diameter side of boot
and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage in boot.
• Be careful not to touch the inside of the boot with the tip of tool.
11. Install new boot bands securely.
CAUTION:
Never reuse boot band.
JPDIF0009ZZ
JPDIF0017ZZ
Grease amount
: Refer to
.
L
: Refer to
.
JPDIF0014ZZ
JPDIF0230ZZ
FAX-110
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
a.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection
and guide slit
at
first.
b.
Pinch projection on the band with suitable pliers to tighten band.
c.
Insert tip of band below end of the pawl.
12. Secure housing and shaft, and then make sure that they are in the correct position when rotating boot.
Install them with new boot band when the mounting positions become incorrect.
13. Install dust shield (left side).
CAUTION:
Never reuse dust shield.
14. Install circular clip to housing (left side).
CAUTION:
Never reuse circular clip.
Support Bearing
1.
Install dust shield on housing.
CAUTION:
Never reuse dust shield.
2.
Press support bearing
onto housing to using the suitable tool
(A).
3.
Install snap ring.
CAUTION:
Never reuse snap ring.
SDIA3557E
SDIA3558E
JPDIF0056ZZ
FRONT DRIVE SHAFT
FAX-111
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4.
Install dust shields.
CAUTION:
Never reuse dust shields.
Dynamic Damper
• Install damper bands securely as shown in the figure.
• Secure dynamic damper with bands in the following specified posi-
tion when removing.
CAUTION:
Never reuse bands.
Wheel Side
For further details, refer to the installation procedure of “
FAX-79, "MR20DD : Removal and Installation"
” for the
drive shaft boot.
MR20DD : Inspection
INFOID:0000000010824419
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
INSPECTION AFTER DISASSEMBLY
JPDIF0127ZZ
PDIA1188J
Demission :
.
FAC0156D
SDIA1190J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст