Nissan X-Trail 32. Manual — part 1075
OIL SEAL
EM-197
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Press in valve oil seal to the height “H” shown in the figure with a
valve oil seal drift [SST: KV10115600] (A).
3.
Install in the reverse order of removal after this step.
FRONT OIL SEAL
FRONT OIL SEAL : Removal and Installation
INFOID:0000000010783800
REMOVAL
1.
Remove the following parts.
• Front fender protector: Refer to
EXT-35, "FENDER PROTECTOR : Exploded View"
• Drive belt: Refer to
EM-166, "Removal and Installation"
.
• Crankshaft pulley: Refer to
.
2.
Remove front oil seal with a suitable tool.
CAUTION:
Be careful not to damage front cover and crankshaft.
INSTALLATION
1.
Apply new engine oil to seal lip.
2.
Install front oil seal so that each seal lip is oriented as shown in
the figure.
Height “H”
: 11.8 - 12.4 mm (0.465 - 0.488 in)
ALBIA0864GB
SEM829E
: Dust seal lip
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
EM-198
< REMOVAL AND INSTALLATION >
[QR25DE]
OIL SEAL
• Press-fit front oil seal until it is flush with front end surface of
front cover using a suitable drift (A) with outer diameter 56 mm
(2.20 in) and inner diameter 48 mm (1.89 in).
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Never touch the grease applied to the oil seal lip.
3.
Install in the reverse order of removal after this step.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000010783801
REMOVAL
1.
Remove the engine and transaxle. Refer to
EM-200, "Removal and Installation"
.
2.
Separate engine from transaxle.
3.
Remove drive plate. Refer to
4.
Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1.
Apply new engine oil to seal lip.
2.
Install rear oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit rear oil seal with a suitable drift (A) [outer diameter
102 mm (4.02 in), inner diameter 86 mm (3.39 in)].
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
ALBIA0865GB
: Dust seal lip
: Oil seal lip
: Drive plate side
: Engine front
PBIC3485J
JSBIA3341ZZ
OIL SEAL
EM-199
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Press in the new rear oil seal
to the position
shown in the
figure.
3.
Install in the reverse order of removal after this step.
: Rear surface of cylinder block
: 0 - 0.5 mm (0 - 0.020 in)
JPBIA3011ZZ
EM-200
< UNIT REMOVAL AND INSTALLATION >
[QR25DE]
ENGINE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000010783802
Removal and Installation
INFOID:0000000010783803
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.
CAUTION:
Torque rod (RH)
Washer
Engine mounting insulator (RH)
Dynamic damper
Engine mounting brock bracket
Engine mounting insulator (LH)
Torque rod bracket (RR)
Torque rod (RR)
4WD models
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSBIA4509GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст