Nissan X-Trail 32. Manual — part 1806
SE-72
< REMOVAL AND INSTALLATION >
THIRD SEAT
• When installing the third seat, lock it to the floor completely
and then perform tightening in the order of 1
→
2 as shown in
the figure.
• When installing striker, tighten fixing bolts according to the
numerical order 1
→
2 as shown in the figure, starting from
vehicle front fixing bolt.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000010713152
DISASSEMBLY
1.
Remove headrest.
2.
Remove bridge board pipe.
a.
Remove under finisher (LH and RH).
i.
Remove under finisher fixing screws
.
ii.
Disengage under finisher fixing pawls, and then remove under
finisher.
JMJIA9719ZZ
: Vehicle front
JMJIA9720ZZ
JMJIA9721ZZ
: Pawl
JMJIA9722ZZ
THIRD SEAT
SE-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
b.
Remove bridge board pipe fixing bolts
, and then remove
bridge board pipe and bridge board as a set.
3.
Remove seatback board.
a.
Disengage seatback board fixing clips.
CAUTION:
• When disengaging clips, be careful of the inserted portion
.
• Before installing the seatback board, check the engaging direction of clip.
b.
Remove release strap.
i.
Remove lever tube
.
ii.
Remove release strap from seatback frame.
JMJIA9723ZZ
: Clip
JMJIA9724ZZ
JMJIA9725ZZ
SE-74
< REMOVAL AND INSTALLATION >
THIRD SEAT
4.
Disengage seatback trim fixing retainers
and magic fasteners
.
5.
Remove the headrest holder by raising it while pinching the
pawls from the bottom of the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left)
6.
Remove seatback trim and seatback pad as a set.
7.
Remove seatback silencer.
8.
Remove hog rings, and then separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
SEAT CUSHION
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000010713153
DISASSEMBLY
1.
Remove bridge board pipe.
a.
Remove under finisher (LH and RH).
JMJIA9726ZZ
PIIB4084J
JMJIA9727ZZ
THIRD SEAT
SE-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
i.
Remove under finisher fixing screws
.
ii.
Disengage under finisher fixing pawls, and then remove under
finisher.
b.
Remove bridge board pipe fixing bolts
, and then remove
bridge board pipe and bridge board as a set.
2.
Remove hinge cover outer fixing screws
, and then remove
hinge cover outer.
3.
Remove seat cushion trim fixing clips
, and then disengage
seat cushion trim fixing magic fastener
.
JMJIA9721ZZ
: Pawl
JMJIA9722ZZ
JMJIA9723ZZ
JMJIA9728ZZ
JMJIA9729ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст