Nissan X-Trail 32. Manual — part 1807
SE-76
< REMOVAL AND INSTALLATION >
THIRD SEAT
4.
Remove seat belt buckle. Refer to
SB-23, "SEAT BELT BUCKLE : Removal and Installation"
5.
Remove seat cushion frame fixing bolts
, and then remove seat cushion and seatback as a set.
6.
Remove hinge bolts
, and then remove seat cushion.
JMJIA9730ZZ
JMJIA9731ZZ
THIRD SEAT
SE-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
7.
Disengage seat cushion fixing retainers
, and then remove seat cushion trim and seat cushion pad as a
set.
8.
Remove seat cushion silencer.
9.
Remove hog rings, and then separate seat cushion trim and seat cushion pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
10. Remove the following parts after removing seat cushion trim and pad.
Hinge Cover Inner
• Remove hinge cover inner fixing clips
, and then remove
hinge cover inner.
Reclining Device Cover Center
1.
Remove reclining device cover center fixing screws
.
2.
Disengage reclining device cover center fixing metal clip,
and then remove reclining device cover center.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
ASSIST STAY
ASSIST STAY : Removal and Installation
INFOID:0000000010713154
REMOVAL
1.
Support third seat with a proper material to prevent it from falling.
Third seat RH
Third seat LH
JMJIA9732ZZ
JMJIA9733ZZ
: Metal clip
JMJIA9734ZZ
SE-78
< REMOVAL AND INSTALLATION >
THIRD SEAT
WARNING:
Injury may occur if third seat is not supported with appropriate material when removing third seat.
2.
Use remover tool (A) to lift metal spring
, and then remove the
assist stay and metal spring from the stud ball portion
as a
unit.
3.
Similarly, disengage other side, and then remove assist stay.
INSTALLATION
Install in the reverse order of removal.
ASSIST STAY : Disposal
INFOID:0000000010713155
1.
Fix assets stay
using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the assist stay, in
numerical order 1
→
2 as shown in the figure.
CAUTION:
• When cutting a hole on assist stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMJIA9737ZZ
JMKIA3336ZZ
A
: 20.0 mm (0.79 in)
: Cut at the groove.
JMKIA3609ZZ
POWER SEAT SWITCH
SE-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
POWER SEAT SWITCH
Removal and Installation
INFOID:0000000010713156
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the front seat. Refer to
SE-41, "Removal and Installation"
2.
Remove the seat cushion outside finisher outerside.
3.
Disconnect power seat switch connector.
4.
Remove power seat switch mounting screws
.
5.
Remove harness clip and remove power seat switch
from
seat cushion outside finisher.
INSTALLATION
Install in the reverse order of removal.
JMJIB0179ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст