Nissan X-Trail 32. Manual — part 2178
TM-670
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000010622873
Removal and Installation
INFOID:0000000010622874
REMOVAL
CAUTION:
• Always apply the parking brake before performing removal and installation.
• Be careful not to cut your hand on heat insulator edges.
1.
Turn ignition switch OFF.
2.
Shift the selector lever to “P” position.
3.
Remove battery tray. Refer to
PG-143, "R9M : Removal and Installation"
.
Control cable
Lock plate
Transaxle assembly
Manual lever
Bracket A
Bracket B
Grommet
CVT shift selector assembly
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA6082GB
CONTROL CABLE
TM-671
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove the control cable nut (
) and remove the control cable
from the manual lever
.
5.
Remove the lock plate
and remove the control cable
from
bracket .
6.
Remove the center console assembly. Refer to
(RHD models).
7.
Disconnect the tip
of control cable from the CVT shift selector
assembly.
8.
Remove socket
from CVT shift selector assembly.
CAUTION:
Never damage pawl of socket.
9.
Disengage the pawls (
) of the grommet
, and pull down-
wards to remove.
10. Lift up the vehicle.
11. Remove the exhaust front tube. Refer to
.
12. Remove the heat plate fixtures
.
: Vehicle front
JSDIA4147ZZ
: Vehicle front
JSDIA4148ZZ
JSDIA5661ZZ
JSDIA5182ZZ
: Vehicle front
JSDIA5214ZZ
TM-672
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CONTROL CABLE
13. Remove the control cable
from bracket
.
14. Remove the control cable from the vehicle.
INSTALLATION
Note the followings and install in the reverse order of removal.
• From below the vehicle, press the grommet
into place until the
pawls (
) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1.
Shift the selector lever and Manual lever to “P” position.
2.
When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
3.
Install the socket
onto the CVT shift selector assembly.
CAUTION:
• Place the socket onto the CVT shift selector assembly,
then fasten it in place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection
INFOID:0000000010622875
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
: Vehicle front
JPDIA0107ZZ
JSDIA5182ZZ
JPDIA0609ZZ
JSDIA1810ZZ
KEY INTERLOCK CABLE
TM-673
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000011009350
Removal and Installation
INFOID:0000000011009351
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Remove the instrument lower panel (driver side) and steering column cover. Refer to
(LHD models),
IP-41, "Removal and Installation"
(RHD models).
2.
Remove the center console. Refer to
IP-25, "Removal and Installation"
(LHD models),
(RHD models).
3.
Press the pawls
of the key interlock cable slider
while slid-
ing it in the direction of the casing cap
, and separate the
adjusting holder
and slider.
4.
Remove the key interlock cable from the shift selector.
Shift selector assembly
Key interlock cable
Clip
Clip
Key cylinder
JSDIA6482ZZ
:Key interlock rod
JSDIA1797ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст