Nissan X-Trail 32. Manual — part 2177
TM-666
< PERIODIC MAINTENANCE >
[CVT: RE0F10G]
CVT FLUID
14. Lift down the vehicle.
15. Stop the engine.
CVT SHIFT SELECTOR
TM-667
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000010622869
Removal and Installation
INFOID:0000000010622870
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Shift the selector lever to “N” position.
2.
Slide the selector lever knob cover
down.
CAUTION:
Never damage the knob cover.
3.
Pull out the lock pin
.
4.
Pull the selector lever knob
and knob cover upwards to
remove them.
5.
Remove the center console assembly. Refer to
(RHD models).
6.
Disconnect the CVT shift selector connector.
7.
Shift the selector lever to “P” position.
Selector lever knob
.
Lock pin
Knob cover
Detent switch*
Park position switch
Shift lock unit
CVT shift selector assembly
:N·m (kg-m, in-lb)
*: With intelligent key system
JSDIA6478GB
JSDIA2778ZZ
TM-668
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CVT SHIFT SELECTOR
8.
Disconnect the key interlock cable from CVT shift selector assembly. Refer to
. (Without intelligent key system)
9.
Remove the control cable from the CVT shift selector assembly with the following procedure.
a.
Disconnect the tip
of control cable from the CVT shift selector
assembly.
b.
Remove socket
from CVT shift selector assembly.
CAUTION:
Never damage the pawl of socket.
10. Remove harness clips from the CVT shift selector with a clip
remover.
11. Remove CVT shift selector assembly mounting bolts.
12. Remove the CVT shift selector assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
• Follow the procedure below and place the selector knob onto the CVT shift selector.
1.
Install the lock pin
onto the selector lever knob
.
2.
Install the knob cover
onto the selector lever knob.
3.
Press the selector lever knob onto the selector lever until it
clicks.
CAUTION:
• When pressing the selector lever knob onto the selector
lever, never press the selector lever knob button.
• Never strike the selector lever knob to press it into place.
4.
After installing selector lever knob, pull the knob to check that it
does not become disconnected.
Disassembly and Assembly
INFOID:0000000010622871
DISASSEMBLY
CAUTION:
Confirm the installation condition of wiring before disassembly.
1.
Remove shift lock unit mounting screws (
).
JSDIA5661ZZ
JPDIA0609ZZ
JSDIA2778ZZ
JSDIA6479ZZ
CVT SHIFT SELECTOR
TM-669
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Remove the shift lock unit
from the CVT shift selector assem-
bly.
3.
Disconnect shift lock solenoid harness connector, park position
switch harness connector, and detent switch harness connec-
tor*.
*: With intelligent key system
4.
Remove park position switch
and detent switch*
from shift
lock unit.
*: With intelligent key system
CAUTION:
Never damage pawls.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection
INFOID:0000000010622872
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
JSDIA6480ZZ
JSDIA6481ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст