Nissan X-Trail 32. Manual — part 1356
CONDENSER
HA-83
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
4.
Remove mounting bolt
, and then disconnect high-pressure
flexible hose from condenser & liquid tank assembly.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser & liq-
uid tank assembly with suitable material such as vinyl tape
to avoid the entry of air.
5.
Remove mounting bolt
, and then disconnect high-pressure
pipe from condenser & liquid tank assembly.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser & liq-
uid tank assembly with suitable material such as vinyl tape
to avoid the entry of air.
6.
Disconnect refrigerant pressure sensor harness connector.
7.
Remove mount bracket mounting bolt and fixing clip. Refer to
8.
Pull up mount bracket, and then remove condenser & liquid tank assembly mounting bolts.
JMIIA3326ZZ
JMIIA3327ZZ
JMIIA3366ZZ
JMIIA3350ZZ
HA-84
< REMOVAL AND INSTALLATION >
[MR20DD]
CONDENSER
9.
Lift the condenser upwards and disconnect condenser & liquid tank assembly from radiator hole
, and
then remove condenser & liquid tank assembly from vehicle underside according to numerical order 1
→
3
indicated by arrows as shown in the figure.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR : Removal and Installation
INFOID:0000000011001070
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
68, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2.
Remove front bumper fascia assembly. Refer to
EXT-15, "Removal and Installation"
3.
Clean refrigerant pressure sensor and its surrounding area, and then remove dust and rust from refriger-
ant pressure sensor.
CAUTION:
Be sure to clean carefully.
4.
Disconnect refrigerant pressure sensor connector.
5.
Use a adjustable wrench or other tool to hold the refrigerant pressure sensor mounting block, and then
remove the refrigerant pressure sensor from the condenser.
CAUTION:
• Never to damage core surface of condenser.
• Cap or wrap the joint of the condenser with suitable material such as vinyl tape avoid the entry
of air.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
JMIIA3351ZZ
JMIIA3366ZZ
CONDENSER
HA-85
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
• Check for leakages when recharging refrigerant. Refer to
HA-86
< REMOVAL AND INSTALLATION >
[MR20DD]
A/C UNIT ASSEMBLY
A/C UNIT ASSEMBLY
Exploded View
INFOID:0000000011001071
REMOVAL
DISASSEMBLY
Cap
Steering member
Instrument stay LH
Instrument stay RH
A/C unit assembly
Drain hose
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JMIIA3519GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст