Nissan X-Trail 32. Manual — part 1304
FSU-20
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
8.
Using jack, lower front suspension member to the position
where the mounting bolts of stabilizer clamp can be removed.
Refer to
FSU-22, "Removal and Installation"
9.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
10. Remove stabilizer bar.
11. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install stabilizer clamp and stabilizer bush as follows.
- The notch
is facing front of the vehicle.
- The slit
is facing rear of the vehicle.
• When installing the stabilizer clamp mounting bolts, tighten in
numerical order.
WEIA0181E
WEIA0182E
: Vehicle front
JPEIA0058ZZ
Temporary tightening
(by hand)
: 1
Temporary tightening
(by tool)
: 2
→
3
Final tightening
(Specified torque)
: 4
→
5
: Vehicle front
JPEIA0245GB
FRONT STABILIZER
FSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• To install stabilizer connecting rod
, tighten the mounting nut with
the hexagonal part
on the stabilizer connecting rod side fixed.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010822763
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
.
JPEIA0252ZZ
FSU-22
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000010822764
Removal and Installation
INFOID:0000000010822765
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
.
3.
Remove wheel sensor. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal and Installation"
4.
Separate stabilizer connecting rod (strut side) from strut. Refer to
FSU-19, "Removal and Installation"
5.
Remove steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
6.
Remove steering gear assembly. Hang steering gear assembly not to interfere with work. Refer to
7.
Separate transverse link from steering knuckle. Refer to
FSU-17, "Removal and Installation"
.
8.
Remove rear torque rod.
• MR20DD: Refer to
EM-56, "Removal and Installation"
• QR25DE: Refer to
EM-200, "Removal and Installation"
.
• R9M: Refer to
EM-366, "Removal and Installation"
.
9.
Set suitable jack under front suspension member.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-31, "Garage Jack and Safety Stand and 2-Pole Lift"
.
• Never damage the front suspension member with a jack.
• Check the stable condition when using a jack.
10. Remove member stay.
11. Remove front suspension member mounting bolts and rebound stopper rubber.
12. Gradually lower the jack to remove front suspension member from vehicle body.
CAUTION:
Operate while checking that jack supporting status is stable.
NOTE:
Front suspension member
Rebound stopper
Member stay
Rebound stopper
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0898GB
FRONT SUSPENSION MEMBER
FSU-23
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Remove suspension member with stabilizer bar and transverse link.
13. Remove the following parts.
• Stabilizer bar: Refer to
FSU-19, "Removal and Installation"
FSU-17, "Removal and Installation"
.
14. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• To install rebound stopper
, insert it with the protrusion aligned
with the hole of member stay
.
• To install member stay and mounting bolts of front suspension
member, temporarily tighten the bolts before tightening to the
specified torque, referring to the tightening method and the numer-
ical order shown below:
• Perform final tightening of bolts and nuts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010822766
INSPECTION AFTER REMOVAL
Check front suspension member for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
JPEIA0248ZZ
Temporary tightening
: 1
→
2
Final tightening
(Specified torque)
: 3
→
4
→
5
→
6
→
7
→
8
→
9
→
10
: Vehicle front
JMEIA0226GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст