Nissan X-Trail 32. Manual — part 188
BRC-218
< REMOVAL AND INSTALLATION >
[WITH VDC (ESP)]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
6.
Disconnect ABS actuator and electric unit (control unit) harness
connector
, follow the procedure below.
a.
Push the pawl
.
b.
Move the lever
in the direction
until locked.
c.
Disconnect ABS actuator and electric unit (control unit) harness
connector.
7.
Loosen flare nut of brake tube using a flare nut wrench, and then remove brake tube between master cyl-
inder and ABS actuator and electric unit (control unit). Refer to
BR-32, "Removal and Installation"
.
8.
LIft up the vehicle.
9.
Remove clip
at the heat insulator lower side to make working
space.
10. Remove bolts
at the ABS actuator and electric unit (control
unit) bracket lower side.
11. Lift down the vehicle.
12. Remove the clip
of the air compressor high-pressure pipe to
make working space.
13. Remove the bolt
at the ABS actuator and electric unit (control
unit) bracket upper side, then remove the ABS actuator and
electric unit as a set with bracket.
CAUTION:
• Never remove and never install ABS actuator and electric
unit (control unit) by holding harness connector.
• Be careful not to drop ABS actuator and electric unit (con-
trol unit) and apply excessive impact to it.
14. Remove bracket from ABS actuator and electric unit (control unit).
INSTALLATION
Note the following, and install in the reverse order of removal.
JSFIA1350ZZ
: Vehicle front
JSFIA2488ZZ
: Vehicle front
JSFIA2489ZZ
: Vehicle front
JSFIA2490ZZ
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-219
< REMOVAL AND INSTALLATION >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• When replacing ABS actuator and electric unit (control unit), remove the inlet hole protector for brake tube
just before performing.
• When installing brake tube, tighten to the specified torque using a flare nut torque wrench so that flare nut
and brake tube are not damaged. Refer to
• Never remove and install actuator by holding actuator harness.
• Bleed air from brake piping after installation. Refer to
BR-14, "Bleeding Brake System"
• Never apply excessive impact to actuator, such as by dropping it.
• After installing the ABS actuator and electric unit (control unit) har-
ness connector
, move the lever
in the direction
to secure
the locking.
• When replacing the ABS actuator and electric unit (control unit), be
sure to perform the configuration. Refer to
RHD
RHD : Exploded View
INFOID:0000000010723765
RHD
JSFIA1352ZZ
ABS actuator and electric unit (con-
trol unit) harness connector
ABS actuator and electric unit (con-
trol unit)
Bracket
To master cylinder secondary side
To master cylinder primary side
To rear LH caliper
To front RH caliper
To front LH caliper
To rear RH caliper
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSFIA2433GB
BRC-220
< REMOVAL AND INSTALLATION >
[WITH VDC (ESP)]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RHD : Removal and Installation
INFOID:0000000010723766
REMOVAL
1.
Disconnect the battery cable from negative terminal. Refer to
BRC-9, "Precautions for Removing Battery
2.
Drain brake fluid. Refer to
.
3.
Remove air duct and air cleaner body. Refer to
EM-308, "Removal and Installation"
.
4.
Disconnect ABS actuator and electric unit (control unit) harness
connector
, follow the procedure below.
a.
Push the pawl
.
b.
Move the lever
in the direction
until locked.
c.
Disconnect ABS actuator and electric unit (control unit) harness
connector.
5.
Loosen flare nut
of brake tube using a flare nut wrench, and
then remove brake tube
between master cylinder and ABS
actuator and electric unit (control unit)
. Refer to
6.
Remove ABS actuator and electric unit (control unit) and bracket.
CAUTION:
• Never remove and never install ABS actuator and electric unit (control unit) by holding harness
connector.
• Be careful not to drop ABS actuator and electric unit (control unit) and apply excessive impact to
it.
7.
Remove bracket, bushing and collar from ABS actuator and electric unit (control unit).
INSTALLATION
Note the following, and install in the reverse order of removal.
• When replacing ABS actuator and electric unit (control unit), remove the inlet hole protector for brake tube
just before performing.
• When installing brake tube, tighten to the specified torque using a flare nut torque wrench so that flare nut
and brake tube are not damaged. Refer to
• Never remove and install actuator by holding actuator harness.
• Bleed air from brake piping after installation. Refer to
BR-78, "Bleeding Brake System"
.
• Never apply excessive impact to actuator, such as by dropping it.
JSFIA1350ZZ
JSFIA2273ZZ
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-221
< REMOVAL AND INSTALLATION >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• After installing the ABS actuator and electric unit (control unit) har-
ness connector
, move the lever
in the direction
to secure
the locking.
• When replacing the ABS actuator and electric unit (control unit), be
sure to perform the configuration. Refer to
JSFIA1352ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст