Nissan X-Trail 32. Manual — part 605
BACK DOOR
DLK-761
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL
1.
Remove headlining. Refer to
INT-37, "Removal and Installation"
2.
Disconnect back door harness connectors
,
and
, and
then remove harness fixing clips
.
3.
Disconnect harness connector
, and then remove harness fix-
ing clips
.
4.
Remove grommet
from roof panel
, and then pull out back
door harness from vehicle body.
5.
Remove air tube
from tube clip
, and then disconnect tube
joint connector
and air tube
(with around view monitor).
: Vehicle front
JMKIB3115ZZ
: Vehicle front
JMKIB3116ZZ
JMKIB3117ZZ
: Vehicle front
JMKIB3118ZZ
DLK-762
< REMOVAL AND INSTALLATION >
[TYPE 3]
BACK DOOR
6.
Remove tube grommet
from roof panel
, and then pull out
air tube from vehicle body.
7.
Disconnect rear washer tube A and rear washer tube B. Refer to
.
8.
Disconnect rear view camera washer tube (with around view monitor). Refer to
ERA WASHER TUBE : Removal and Installation"
9.
Remove tube grommet
from roof panel
, and then pull out
rear washer tube B and rear camera washer tube from vehicle
body.
10. Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
11. Remove back door stay from back door. Refer to
DLK-765, "BACK DOOR STAY : Removal and Installa-
12. Remove back door hinge mounting nuts of back door and remove back door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, perform the fitting adjustment. Refer to
DLK-763, "BACK DOOR ASSEMBLY :
• After installation, check whether harness is not pinched. If harness is pinched, pull harness down-
ward lightly.
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check that door opens and closes normally. Refer to
BACK DOOR ASSEMBLY : Inspection
INFOID:0000000010728570
1.
Open and close the back door. Check that door hinge rotation portion moves smoothly.
JMKIB3119ZZ
JMKIB3120ZZ
BACK DOOR
DLK-763
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Check back door hinge rotating part for poor lubrication. Apply
body grease if necessary.
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000010728571
FITTING ADJUSTMENT
: Body grease
JMKIB3113ZZ
Back door assembly
Roof panel
Body side outer panel
Rear bumper fascia
Back door hinge
Bumper rubber
JMKIB3480GB
DLK-764
< REMOVAL AND INSTALLATION >
[TYPE 3]
BACK DOOR
Fitting Adjustment Standard
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
When back door is reused.
Unit: mm [in]
When back door is replaced.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Loosen back door hinge mounting nuts of back door side.
2.
Loosen bumper rubber.
3.
Remove luggage rear plate mask. Refer to
INT-41, "LUGGAGE REAR PLATE : Removal and Installation"
.
4.
Loosen back door striker mounting TORX bolts.
5.
Position back door lock assembly and engage back door striker. Check back door lock assembly and back
door striker for looseness.
6.
Adjust the clearance and surface height of back door according to the fitting standard dimension by back
door hinge and bumper rubber.
Back door striker
TORX bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Difference
(LH/RH,
MAX)
Back door – Roof panel
–
D
Clearance
5.0 – 9.0
[0.197 – 0.354]
—
E
Surface height
(
−
3.0) – (+1.0)
[(
−
0.118) – (+0.039)]
—
Back door – Body side outer
panel
–
F
Clearance
3.0 – 7.0
[0.118 – 0.276]
<2.0
[0.079]
G
Surface height
(
−
3.0) – (+1.0)
[(
−
0.118) – (+0.039)]
—
Back door – Rear bumper
fascia
–
H
Clearance
5.5 – 9.5
[0.217 – 0.374]
—
Portion
Standard
Difference
(LH/RH,
MAX)
Back door – Roof panel
–
D
Clearance
5.1 – 9.1
[0.201 – 0.358]
—
E
Surface height
(
−
2.0) – (+2.0)
[(
−
0.079) – (+0.079)]
—
Back door – Body side outer
panel
–
F
Clearance
2.5 – 6.5
[0.098 – 0.256]
<2.0
[0.079]
G
Surface height
(
−
3.3) – (+0.7)
[(
−
0.130) – (+0.028)]
—
Back door – Rear bumper
fascia
–
H
Clearance
5.7 – 9.7
[0.224 – 0.382]
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст