Nissan X-Trail 32. Manual — part 603
REAR DOOR
DLK-753
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010728561
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door harness grommet
from vehicle body
,
and then pull out rear door harness.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolt of door check link of vehicle body side.
4.
Remove door hinge mounting nuts of door side, and then remove door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-754, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check that door opens and closes normally. Refer to
.
Door striker
TORX bolt
Grommet
Rear door weather-strip clip
Rear door weather-strip
Rear door weather-strip clip
: Clip
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3071ZZ
JMKIB3072ZZ
DLK-754
< REMOVAL AND INSTALLATION >
[TYPE 3]
REAR DOOR
DOOR ASSEMBLY : Inspection
INFOID:0000000010728562
1.
Open and close the door. Check that door hinge and check link rotation portion moves smoothly.
2.
Check door hinge rotating part for poor lubrication. Apply body grease if necessary.
• Door hinge (upper)
• Door hinge (lower)
3.
Check door check link rotating part for poor lubrication. Apply
body grease if necessary.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010728563
FITTING ADJUSTMENT
: Body grease
JMKIB0329ZZ
: Body grease
JMKIB0321ZZ
: Body grease
JMKIB0322ZZ
REAR DOOR
DLK-755
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Front fender
Front door
Rear door
Body side outer
Door striker
TORX bolt
Front door hinge
Rear door hinge (upper)
Rear door hinge (lower)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3479GB
DLK-756
< REMOVAL AND INSTALLATION >
[TYPE 3]
REAR DOOR
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
2.
Loosen door hinge mounting nuts of door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts of door side.
5.
Loosen door hinge mounting nuts and bolts of vehicle body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment, tighten bolts and nuts to the specified torque.
CAUTION:
After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts and
nuts.
8.
Install center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal and
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010728564
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• After installation, perform the fitting adjustment. Refer to
DLK-754, "DOOR ASSEMBLY : Adjust-
• After installation, check that door opens and closes normally. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010728565
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-753, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
Portion
Standard
Front door – Rear door
–
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Rear door – Body side outer
–
L
Clearance
3.0 – 5.0
[0.118 – 0.197]
M
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст