Nissan X-Trail 32. Manual — part 2248
WASHER NOZZLE AND TUBE
WW-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
RHD models
Unit: mm (in)
• Use washer nozzle adjuster (A) for front washer nozzle
adjust-
ment.
CAUTION:
Never use needle or small pin.
REAR WASHER NOZZLE
REAR WASHER NOZZLE : Removal and Installation
INFOID:0000000010785466
REMOVAL
1.
Remove high-mounted stop lamp. Refer to
EXL-207, "Removal and Installation"
(for LED headlamp) or
EXL-392, "Removal and Installation"
(for Halogen headlamp).
JMLIA5015ZZ
Black printed frame line
: Spray area
Driver side
Passenger side
X
409 (16.10)
356 (14.02)
127 (5.00)
103 (4.06)
103 (4.06)
133 (5.24)
354 (13.94)
409 (16.10)
Y
398 (15.67)
100 (3.94)
93 (3.66)
496 (19.53)
497 (19.57)
80 (3.15)
90 (3.54)
380 (14.96)
JMLIA1539ZZ
WW-100
< REMOVAL AND INSTALLATION >
WASHER NOZZLE AND TUBE
2.
Disconnect portion
of rear washer tube C from joint.
3.
While holding rear washer nozzle fixing pawls, push up in the
direction of the arrow in the figure, and then remove rear washer
nozzle.
4.
Remove rear washer nozzle from rear washer tube C.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Adjust rear washer nozzle spray position. Refer to
WW-100, "REAR WASHER NOZZLE : Inspection and
REAR WASHER NOZZLE : Inspection and Adjustment
INFOID:0000000010785467
INSPECTION
Rear Check Valve Inspection
Check that air can pass through the hose by blowing forward [toward
the nozzle], and check that air cannot pass through by sucking.
ADJUSTMENT
Rear Washer Nozzle Spray Position Adjustment
JMLIA5011ZZ
: Pawl
JMLIA5012ZZ
JPLIA1659ZZ
WASHER NOZZLE AND TUBE
WW-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening
and
move up/down and left/right to adjust the spray position.
FRONT WASHER TUBE
FRONT WASHER TUBE : Removal and Installation
INFOID:0000000010785468
REMOVAL
1.
Remove cowl top cover. Refer to
EXT-25, "Removal and Installation"
.
2.
Disconnect front washer tube C from front washer nozzle RH.
3.
Disconnect front washer tube D from front washer nozzle LH.
4.
Disconnect front washer tube C and D from check valve.
5.
Disconnect check valve from front washer tube B.
6.
Disconnect front washer tube B from cowl top cover.
7.
Disconnect joint from front washer tube A.
8.
Remove fender protector RH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
Rear washer nozzle
Spray range
Spray position
X
Y
10.6 (0.42)
20.6 (0.81)
12.8 (0.50)
15.5 (0.61)
12.8 (0.50)
15.5 (0.61)
10.6 (0.42)
20.6 (0.81)
JMLIA5016ZZ
JPLIA1661ZZ
WW-102
< REMOVAL AND INSTALLATION >
WASHER NOZZLE AND TUBE
9.
Disconnect front washer tube A from washer tank and fixing clips
.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Align washer tube marking to the vehicle installation position.
REAR WASHER TUBE
REAR WASHER TUBE : Removal and Installation
INFOID:0000000010785469
REMOVAL
CAUTION:
Replacement of a single part is not possible due to the adoption of rear washer tube B. For replace-
ment, replace back door assembly as a set.
1.
Remove fender protector RH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
2.
Disconnect rear washer tube A
from washer pump.
3.
Remove rear washer tube A
from fixing clips
, and then remove grommet
, and then pull in rear
washer tube A of inside the vehicle.
4.
Remove dash side finisher RH. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
5.
Remove center pillar lower garnish RH. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
6.
Remove luggage side upper finisher RH. Refer to
INT-45, "LUGGAGE SIDE UPPER FINISHER :
.
JMLIA5014ZZ
JMLIA5017ZZ
JMLIA5019ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст