Nissan X-Trail 32. Manual — part 598
HOOD
DLK-733
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Before installation of hood, apply anticorrosive agent onto the mounting surface of the hood hinge.
• After installing, perform hood fitting adjustment. Refer to
DLK-733, "HOOD ASSEMBLY : Adjust-
• Apply touch-up paint to the body color if the paint around the hinge is peeled off during removal.
• After installation, check that hood opens and closes normally. Refer to
.
HOOD ASSEMBLY : Inspection
INFOID:0000000010728541
1.
Open and close the hood. Check that hood hinge rotation portion moves smoothly.
2.
Check hood hinge rotating part for poor lubrication. If necessary,
apply grease.
HOOD ASSEMBLY : Adjustment
INFOID:0000000010728542
FITTING ADJUSTMENT
: Body grease
JMKIB2933ZZ
DLK-734
< REMOVAL AND INSTALLATION >
[TYPE 3]
HOOD
Fitting Adjustment Standard
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Hood assembly
Front grille
Front combination lamp
Front fender
Hood bumper rubber
Hood hinge
Hood lock assembly
: Vehicle front
: N·m (kg-m, ft-lb)
: Body grease
JMKIB2934GB
HOOD
DLK-735
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove hood lock assembly mounting bolts, and then remove hood lock assembly.
2.
Adjust the surface height of hood assembly according to the specified value by rotating hood bumper rub-
ber.
3.
Loosen hood hinge mounting bolts, and then adjust clearance of hood according to the specified value by
moving the hood assembly.
4.
Tighten hood hinge mounting bolts to the specified torque.
5.
Install hood lock assembly and temporary tighten hood lock
assembly mounting bolts, and then position hood lock assembly
and engage primary striker
. Check hood lock assembly
and primary striker for looseness.
6.
Move hood lock assembly laterally until the center of primary striker and hood lock assembly are vertical
when viewed from the front.
7.
Tighten hood lock assembly mounting bolts to the specified torque.
8.
After adjusting, check that hood opens and closes normally. Refer to
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000010728543
REMOVAL
1.
Remove hood assembly. Refer to
DLK-732, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove upper mounting bolt
of front fender assembly
.
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front grille
–
D
Clearance
7.2 – 11.2
[0.283 – 0.441]
—
Hood –
Front combination lamp
–
E
Clearance
7.0 – 11.0
[0.276 – 0.433]
—
Hood – Front fender
–
F
Clearance
2.5 – 4.5
[0.098 – 0.177]
< 1.4 [0.055]
G
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
< 1.4 [0.055]
JMKIB3550ZZ
JMKIB2955ZZ
DLK-736
< REMOVAL AND INSTALLATION >
[TYPE 3]
HOOD
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Before installation of hood hinge, apply anticorrosive agent onto the mounting surface of the hood
hinge.
• After installation, perform hood fitting adjustment. Refer to
DLK-733, "HOOD ASSEMBLY : Adjust-
• Apply touch-up paint to the body color if the paint around the hinge is peeled off during removal.
• After installation, check that hood opens and closes normally. Refer to
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010728544
CAUTION:
2 workers are required to support the hood.
REMOVAL
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2.
Pull hood support rod from grommet and remove it.
INSTALLATION
Install in the reverse order of removal.
RADIATOR CORE SEAL
RADIATOR CORE SEAL : Removal and Installation
INFOID:0000000010728545
REMOVAL
1.
Apply protective tape (A) to hood assembly
around radiator
core seal
fixing clips for preventing damage.
2.
Disengage fixing clips on the reverse side of radiator core seal
using a remover tool (A).
CAUTION:
Never damage hood assembly.
3.
Remove radiator core seal from hood assembly.
INSTALLATION
JMKIB2956ZZ
: Clip
JMKIB2957ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст