Nissan X-Trail 32. Manual — part 377
DAS
C1BC2-00 REAR RIGHT WHEEL SENSOR
DAS-249
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
4.
Perform “All DTC Reading”.
Are DTC “C1BC2-00”, “U1000-00” or other DTC detected?
YES (“C1BC2-00”)>>Replace the chassis control module. Refer to
DAS-278, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS-250
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BC3-00 REAR LEFT WHEEL SENSOR
C1BC3-00 REAR LEFT WHEEL SENSOR
DTC Description
INFOID:0000000010721754
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Rear left wheel sensor
• Rear left sensor rotor
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active trace control function
• Active ride control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Start the engine.
2.
Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.
3.
Stop the vehicle.
4.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
5.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BC3-00” detected?
YES
>> Proceed to
DAS-250, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010721755
1.
REAR LEFT WHEEL SENSOR SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC3-00
RL WHEEL SENSOR
(Rear left wheel sensor)
When a malfunction is detected in rear left wheel sensor system.
DAS
C1BC3-00 REAR LEFT WHEEL SENSOR
DAS-251
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
4.
Perform “All DTC Reading”.
Are DTC “C1BC3-00”, “U1000-00” or other DTC detected?
YES (“C1BC3-00”)>>Replace the chassis control module. Refer to
DAS-278, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS-252
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BC4-00 DECEL G SENSOR
C1BC4-00 DECEL G SENSOR
DTC Description
INFOID:0000000010721756
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following function is suspended.
• Active ride control (brake control) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BC4-00” detected?
YES
>> Proceed to
DAS-252, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010721757
1.
CHECK DECEL G SENSOR SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Are DTC “C1BC4-00”, “U1000-00” or other DTC detected?
YES (“C1BC4-00”)>>Replace the chassis control module. Refer to
DAS-278, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC4-00
DECEL G SENSOR
(Decel G sensor)
When a malfunction is detected in decel G sensor system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст