Nissan X-Trail 32. Manual — part 378
DAS
C1BC5-00 SIDE G SENSOR
DAS-253
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BC5-00 SIDE G SENSOR
DTC Description
INFOID:0000000010721758
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active trace control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BC5-00” detected?
YES
>> Proceed to
DAS-253, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010721759
1.
CHECK SIDE G SENSOR SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Are DTC “C1BC5-00”, “U1000-00” or other DTC detected?
YES (“C1BC5-00”)>>Replace the chassis control module. Refer to
DAS-278, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC5-00
SIDE G SENSOR
(Side G sensor)
When a malfunction is detected in side G sensor system.
DAS-254
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BC6-00 PRESSURE SENSOR
C1BC6-00 PRESSURE SENSOR
DTC Description
INFOID:0000000010721760
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active trace control function
• Active ride control (brake control) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BC6-00” detected?
YES
>> Proceed to
DAS-254, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010721761
1.
CHECK BRAKE FLUIFD PRESSURE SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Are DTC “C1BC6-00”, “U1000-00” or other DTC detected?
YES (“C1BC6-00”)>>Replace the chassis control module. Refer to
DAS-278, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (other DTC)>>Check the DTC.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BC6-00
PRESSURE SENSOR
(Pressure sensor)
When a malfunction is detected in brake fluid pressure system.
DAS
C1BC6-00 PRESSURE SENSOR
DAS-255
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
NO
>> INSPECTION END
DAS-256
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
U1000-00 CAN COMM CIRCUIT
U1000-00 CAN COMM CIRCUIT
DTC Description
INFOID:0000000010721762
DTC DETECTION LOGIC
POSSIBLE CAUSE
• CAN communication system
FAIL-SAFE
The following functions are suspended.
• Active trace control function
• Active engine brake function
• Active ride control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “U1000-00” detected?
YES
>> Proceed to
DAS-256, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010721763
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
U1000-00
CAN COMM CIRCUIT
(CAN communication circuit)
When CAN communication signal is not continuously transmitted or received for 2
seconds or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст