Nissan X-Trail 32. Manual — part 1984
ST-14
< REMOVAL AND INSTALLATION >
STEERING COLUMN
11. Remove steering shaft mounting bolt
(steering gear side).
12. Remove steering shaft from steering gear assembly.
CAUTION:
When removing steering shaft, never insert a tool, such as
a screwdriver, into the yoke groove to pull out the upper
joint. In case of the violation of the above, replace steering
shaft with a new one.
13. Remove steering shaft mounting bolt
(steering column
assembly side).
14. Remove steering shaft from steering column assembly.
CAUTION:
• Place a matching mark
on both steering shaft
and
steering column assembly
before removing steering
shaft.
• When removing steering shaft, never insert a tool, such
as a screwdriver, into the yoke groove to pull out the
upper joint. In case of the violation of the above, replace
steering shaft with a new one.
15. Remove the steering column assembly mounting nut, and then remove steering column assembly.
CAUTION:
When removing the mounting nut, be careful not to drop the steering column assembly.
16. Perform inspection after removal. Refer to
INSTALLATION
CAUTION:
• Never impact on the axis when removing steering column assembly.
• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.
• If the dash seal is deformed, replace it. (It becomes the cause for the water leak.)
Note the following, and install in the reverse order of removal.
• For steering shaft mounting bolt direction, refer to
. (Do not insert it from the other
side.)
JSGIA1443ZZ
JSGIA1444ZZ
JSGIA1445ZZ
STEERING COLUMN
ST-15
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• When connecting steering shaft joint part
and column shaft,
make sure the bolt is securely seated in groove
of column shaft
before final tightening.
• When installing the steering column assembly
, tighten to the
specified torque in the numerical order shown below:
• After installing steering column assembly, perform self-diagnosis with CONSULT to ensure correct opera-
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010839337
INSPECTION AFTER REMOVAL
Check the following items and replace, if necessary.
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Measure steering column rotating torque using a preload gauge
(A) (SST: ST3127S000). Replace steering column assembly if the
rotating torque is outside the standard.
• Measure the length “L” shown in the figure, if vehicle has been
involved in a minor collision. Replace steering column assembly
(with motor, reduction gear, sensor) if “L” is outside the standard.
INSPECTION AFTER INSTALLATION
SGIA1295E
Tightening order
1
→
2
→
3
→
4
JSGIA1566ZZ
Rotating torque
: Refer to
JSGIA1480ZZ
Steering column
length (L)
: Refer to
JSGIA1446ZZ
ST-16
< REMOVAL AND INSTALLATION >
STEERING COLUMN
Check the following items and replace, if necessary.
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Check tilt and telescopic mechanism operating range “T”, “L” as
shown in the figure.
• Rotate steering wheel to check for decentered condition, binding,
noise, or excessive steering effort.
• Check the steering wheel play, neutral position steering wheel,
steering wheel turning torque, and front wheel turning angle.
- Steering wheel play: Refer to
.
- Neutral position steering wheel, steering wheel turning torque, and front wheel turning angle: Refer to
• Adjust neutral position of steering angle sensor. Refer to
.
Tilt operating range (T)
: Refer to
.
Telescopic operating
range (L)
: Refer to
.
JSGIA1447ZZ
STEERING SHAFT
ST-17
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING SHAFT
Exploded View
INFOID:0000000010839338
Removal and Installation
INFOID:0000000010839339
REMOVAL
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
1.
Set vehicle to the straight-ahead position.
2.
Place the tilt to the highest level.
3.
Remove instrument lower panel. Refer to
IP-14, "Removal and Installation"
(RHD).
4.
Remove hole cover.
5.
Remove steering shaft mounting bolt
(steering gear side).
6.
Remove steering shaft from steering gear assembly.
CAUTION:
When removing steering shaft, never insert a tool, such as
a screwdriver, into the yoke groove to pull out the upper
joint. In case of the violation of the above, replace steering
shaft with a new one.
Steering column assembly
Steering shaft
Hole cover
Clip
Dash seal
,
: Tightening must be done following the installation procedure.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSGIA1448GB
JSGIA1443ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст