Nissan X-Trail 32. Manual — part 1985
ST-18
< REMOVAL AND INSTALLATION >
STEERING SHAFT
7.
Remove steering shaft mounting bolt
(steering column
assembly side).
8.
Remove steerign shaft from steering column assembly.
CAUTION:
• Place a matching mark
on both steering shaft
and
steering column assembly
before removing steering
shaft.
• When removing steering shaft, never insert a tool, such
as a screwdriver, into the yoke groove to pull out the
upper joint. In case of the violation of the above, replace
steering shaft with a new one.
9.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
• For steering shaft and steering column assembly mounting bolt direction, refer to
.
(Do not insert it from the other side.)
• When connecting steering shaft joint part
and column shaft,
make sure the bolt is securely seated in groove
of column shaft
before final tightening.
• Perform inspection after installation. Refer to
.
• Tighten the mounting bolt
of steering shaft (steering gear side)
to the specified torque.
JSGIA1444ZZ
JSGIA1445ZZ
Tightening torque
: 26 (2.7, 19) - 36 (3.7, 27) N·m
SGIA1295E
Tightening torque
: 45 (4.6, 33) - 55 (5.6, 41) N·m
JSGIA1443ZZ
STEERING SHAFT
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Inspection
INFOID:0000000010839340
INSPECTION AFTER REMOVAL
Check the following items and replace, if necessary.
• Check each part of steering shaft for damage or other malfunctions. Replace if there are any abnormal con-
ditions.
INSPECTION AFTER INSTALLATION
Check the following items and replace, if necessary.
• Check each part of steering shaft for damage or other malfunctions. Replace if there are any abnormal con-
ditions.
• Rotate steering wheel to check for decentered condition, binding, noise, or excessive steering effort.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning torque, and front
wheel turning angle.
- Steering wheel play: Refer to
.
- Neutral position steering wheel, steering wheel turning torque, and front wheel turning angle: Refer to
• Adjust neutral position of steering angle sensor. Refer to
.
ST-20
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
LHD
LHD : Exploded View
INFOID:0000000010839341
REMOVAL
DISASSEMBLY
Steering gear assembly
Heat insulator
Front suspension member
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSGIA1553GB
JSGIA1554GB
STEERING GEAR AND LINKAGE
ST-21
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
CAUTION:
• Apply Molywhite LSG (manufactured by Kyodo yushi) to steering rack of proper quantity, if the
grease of steering rack adheres into boot inside in removing boots and the grease is removed.
• Never apply the grease to the surface between steering rack and inner socket screw part.
RHD
RHD : Exploded View
INFOID:0000000010839342
REMOVAL
DISASSEMBLY
Outer socket
Outer socket lock nut
Inner socket
Boot clamp (small diameter)
Boot
Boot clamp (large diameter)
Gear housing assembly
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
1: Apply Molywhite LSG or equivalent.
2: Apply RENOLIT JP1619
Steering gear assembly
Heat insulator
Front suspension member
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPGIA0001GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст