Nissan X-Trail 32. Manual — part 1635
PB-66
< BASIC INSPECTION >
CHANGE OF SYSTEM MODE
6.
RELEASE OF REAR BRAKE CALIPER
Perform the release of rear brake caliper: Refer to
>> GO TO 7.
7.
CHANGE OF SYSTEM MODE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “SYSTEM MODE CHANGE” according to this order.
CAUTION:
Never operate the parking brake switch.
2.
Touch “START”.
3.
Check display item “FACTORY MODE”.
Is the inspection result “Off”?
YES
>> GO TO 8.
NO
>> Perform change of system mode again.
8.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Pull parking brake switch to activate electric parking brake.
2.
Push parking brake switch to release electric parking brake.
3.
Perform “EHS/PKB” self-diagnosis.
Is malfunction detected?
YES
>> Check the DTC. Refer to
. GO TO 9.
NO
>> GO TO 9.
9.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.
2.
Erase self-diagnosis results memory of “EHS/PKB”.
Is the memory erased?
YES
>> INSPECTION END
NO
>> Check the items indicated by the self-diagnosis.
AUTOMATIC ACTIVATION ON SETTING
PB-67
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
AUTOMATIC ACTIVATION ON SETTING
Description
INFOID:0000000010728188
CAUTION:
When the following operations are performed, always use CONSULT, for performing “AUTO ACTIVA-
TION ON (AT/CVT)” of “WORK SUPPORT”.
NOTE:
This work is CVT models.
×
: Required
—: not required
Work Procedure
INFOID:0000000010728189
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Setting electric parking brake automatically operation is ON
NOTE:
This work is CVT models.
1.
AUTO ACTIVATION ON (AT/CVT)
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “AUTO ACTIVATION ON (AT/CVT)” according to this order.
CAUTION:
Never operate the parking brake switch.
2.
Touch “START”.
3.
Check display item “Auto Apply for CVT”.
Is the inspection result “AVAILABLE”?
YES
>> GO TO 2.
NO
>> Perform “AUTO ACTIVATION ON (AT/CVT)” again.
2.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Pull parking brake switch to activate electric parking brake.
2.
Push parking brake switch to release electric parking brake.
3.
Perform “EHS/PKB” self-diagnosis.
Is malfunction detected?
YES
>> Check the DTC. Refer to
. GO TO 3.
NO
>> GO TO 3.
3.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.
2.
Erase self-diagnosis results memory of “EHS/PKB”.
Is the memory erased?
YES
>> INSPECTION END
Procedure
AUTO ACTIVATION ON (AT/CVT)
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Replacing rear brake caliper assembly
—
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Setting electric parking brake automatically operation is ON
×
PB-68
< BASIC INSPECTION >
AUTOMATIC ACTIVATION ON SETTING
NO
>> Check the items indicated by the self-diagnosis.
C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE
PB-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
DTC/CIRCUIT DIAGNOSIS
C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE
DTC Description
INFOID:0000000010722952
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Electric parking brake control module
• Parking brake switch
FAIL-SAFE
Type 1
Only mechanical release is available.
Type 2
Only mechanical release is available.
Type 3
Only mechanical release is available.
Type 4
Only mechanical release is available.
Type 5
Automatic apply and release are prohibited.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds after turning ignition switch OFF or ON.
2.
Push the parking brake switch.
CAUTION:
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
Type
C10C8
CONTROL MODULE
(CONTROL MODULE)
INTERNAL ELECTRIC
MALFNCTN
(INTERNAL ELECTRIC
MALFNCTN)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of hardware)
1
WATCHDOG/SAFETY
µ
C
ERROR
(Watchdog/safety
µ
C error)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of communica-
tion)
2
SUPERVISION SOFT-
WARE ERROR
(Supervision software error)
When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of software)
3
EVENT INFORMATION
(Event information)
When there is an internal malfunction in the electric park-
ing brake control module. (Maintenance mode)
4
NOT CONFIGURED
(Not configured)
When variant coding is incomplete.
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст