Nissan X-Trail 32. Manual — part 717
DMS-16
< DTC/CIRCUIT DIAGNOSIS >
[ECO MODE]
ECO MODE SWITCH
5.
CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH
1.
Disconnect combination meter connector M43.
2.
Check the continuity between combination meter harness connector terminal and ECO mode switch har-
ness connector terminal.
3.
Also check harness for short to ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK GROUND CIRCUIT
1.
Turn OFF the headlamp.
2.
Turn ignition switch OFF.
3.
Check continuity between ECO mode switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK ECO MODE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECO mode switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between ECO mode switch harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> GO TO 8.
8.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check the continuity between ECO mode switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning parts.
9.
CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (PART 1)
1.
Disconnect combination meter harness connector M34.
Combination meter
ECO mode switch
Continuity
Connector
Terminal
Connector
Terminal
M42
43
M9
3
Existed
ECO mode switch
—
Continuity
Connector
Terminal
M9
4
Ground
Existed
ECO mode switch
Voltage
(Approx.)
Connector
+
−
Terminal
M9
1
2
10 V
ECO mode switch
—
Continuity
Connector
Terminal
M9
2
Ground
Existed
DMS
ECO MODE SWITCH
DMS-17
< DTC/CIRCUIT DIAGNOSIS >
[ECO MODE]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
2.
Check continuity between combination meter harness connector terminal and ECO mode switch harness
connector terminal.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
10.
CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (PART 2)
Check continuity between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace malfunctioning parts.
11.
CHECK COMBINATION METER INPUT/OUTPUT SIGNAL
1.
Connect all of disconnected connectors.
2.
Check input/output signal of combination meter. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace combination meter. Refer to
MWI-151, "Removal and Installation"
12.
CHECK ECO MODE SWITCH
Check ECO mode switch. Refer to
DMS-17, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace ECO mode switch. Refer to
MWI-151, "Removal and Installation"
Component Inspection
INFOID:0000000010623754
1.
CHECK ECO MODE SWITCH
Check continuity between ECO mode switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ECO mode switch. Refer to
DMS-19, "Removal and Installation"
Combination meter
ECO mode switch
Continuity
Connector
Terminal
Connector
Terminal
M34
9
M9
1
Existed
Combination meter
—
Continuity
Connector
Terminal
M34
9
Ground
Not existed
ECO mode switch
Condition
Continuity
Terminal
1 – 2
ECO mode switch is depressed.
Existed
ECO mode switch is released.
Not existed
DMS-18
< SYMPTOM DIAGNOSIS >
[ECO MODE]
THE ECO MODE INDICATOR DOES NOT TURN ON
SYMPTOM DIAGNOSIS
THE ECO MODE INDICATOR DOES NOT TURN ON
Description
INFOID:0000000010623755
The ECO mode indicator does not turn ON when the ECO mode switch is operated.
Diagnosis Procedure
INFOID:0000000010623756
1.
PERFORM COMBINATION METER ON BOARD DIAGNOSIS
Perform combination meter on board diagnosis and check ECO mode indicator is turns ON. Refer to
.
Is the check result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-151, "Removal and Installation"
2.
CHECK DTC (TCM)
With CONSULT
1.
Start the engine.
2.
Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
(R9M).
NO
>> GO TO 3.
3.
CHECK DTC (ECM)
With CONSULT
Check “Self Diagnostic Results” in “ENGINE”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
(R9M).
NO
>> GO TO 4.
4.
CHECK DTC (COMBINATION METER)
With CONSULT
Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?
YES
>> Check DTC detected item. Refer to
NO
>> GO TO 5.
5.
CHECK COMBINATION METER INPUT/OUTPUT SIGNAL
With CONSULT
1.
Select “Data Monitor” in “METER/M&A”.
2.
Select “ECO MODE IND”.
3.
Check that “ECO MODE IND” turns ON/OFF when ECO mode switch is operated. Refer to
Is any DTC detected?
YES
>> Replace combination meter. Refer to
MWI-151, "Removal and Installation"
NO
>> GO TO 6.
6.
CHECK ECO MODE SWITCH CIRCUIT
Check ECO mode switch circuit. Refer to
.
Is the check result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning parts.
DMS
ECO MODE SWITCH
DMS-19
< REMOVAL AND INSTALLATION >
[ECO MODE]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
REMOVAL AND INSTALLATION
ECO MODE SWITCH
Removal and Installation
INFOID:0000000010623757
REMOVAL
1.
Remove instrument lower panel (driver side) or instrument lower panel RH (for Australia). Refer to
(LHD models),
IP-41, "Removal and Installation"
(RHD models).
2.
Remove switch bracket from instrument lower panel.
3.
Remove ECO mode switch
from switch bracket.
NOTE:
For design of ECO mode switch, refer to
INSTALLATION
Install in the reverse order of removal.
JSOIA1375ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст