Nissan X-Trail 32. Manual — part 990
P1011 SWIRL CONTROL VALVE ACTUATOR
EC-1089
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Also check harness for short to power and short to ground.
Is the inspection result normal?
YES
>> Replace intake manifold runner control valve.
NO
>> Repair or replace error-detected parts.
+
-
Continuity
ECM
Intake manifold runner con-
trol valve
Connector
Terminal
Connector
Terminal
F117
49
F147
4
Existed
F118
112
1
121
3
125
2
EC-1090
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P1012 SWIRL CONTROL VALVE ACTUATOR
P1012 SWIRL CONTROL VALVE ACTUATOR
DTC Description
INFOID:0000000010935777
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (Intake manifold runner control valve position sensor circuit is open or shorted.)
• Intake manifold runner control valve stuck
• Intake manifold runner control valve actuator
• Intake manifold runner control valve position sensor
FAIL-SAFE
Stop intake manifold runner control valve control (Fully open position)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Perform “Intake Manifold Runner Control Valve Position Learning”. Refer to
.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC-1090, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010935778
1.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
1.
Turn ignition switch OFF.
2.
Check ECM harness connector connection F406 and F407.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE HARNESS CONNECTOR CONNECTIONS
Check intake manifold runner control valve harness connector connection F427.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check the continuity between ECM harness connector and intake manifold runner control valve harness
connector.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1012
SWIRL FLAP
(Swirl flap)
• 1.DEF: OFFSET IMPLAUSIBLE
ECM detects the intake manifold runner control valve regulation error.
P1012 SWIRL CONTROL VALVE ACTUATOR
EC-1091
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Also check harness for short to power and short to ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
PERFORM INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION LEARNING
1.
Perform “Intake Manifold Runner Control Valve Position Learning”.
2.
Check DTC.
Is the DTC P1012 displayed again?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE FITTING CONDITION
Check intake manifold runner control valve fitting condition.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace error-detected parts.
+
-
Continuity
ECM
Intake manifold runner con-
trol valve
Connector
Terminal
Connector
Terminal
F117
49
F147
4
Existed
F118
112
1
121
3
125
2
EC-1092
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P1013 SWIRL CONTROL VALVE POSITION SENSOR
P1013 SWIRL CONTROL VALVE POSITION SENSOR
DTC Description
INFOID:0000000010935779
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (Intake manifold runner control valve position sensor circuit is open or shorted.)
• Intake manifold runner control valve position sensor
FAIL-SAFE
Stop intake manifold runner control valve control (Fully open position)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC-1092, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010935780
1.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
1.
Turn ignition switch OFF.
2.
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE HARNESS CONNECTOR CONNECTIONS
Check intake manifold runner control valve harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POWER SUPPLY CIRCUIT
1.
Disconnect intake manifold runner control valve.
2.
Turn ignition switch ON.
3.
Check the power supply of the intake manifold runner control valve.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1013
SWIRL FLAP POSITION SENSOR
(Swirl flap position sensor)
• 1.DEF: SIGNAL INCOHERENCE
• A voltage of intake manifold runner control valve position sensor is more
than 4.8 V for 1 second.
• A voltage of intake manifold runner control valve position sensor is less
than 0.2 V for 1 second.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст