Nissan X-Trail 32. Manual — part 2183
TM-690
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000010622901
Removal and Installation
INFOID:0000000010622902
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
Differential Side Oil Seal (Left Side)
1.
Remove front drive shaft. Refer to
FAX-50, "R9M : Removal and Installation"
2.
Remove differential side oil seal
using an oil seal remover (A)
(commercial service tool).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
Differential Side Oil Seal (Right Side)
1.
Remove front drive shaft. Refer to
FAX-50, "R9M : Removal and Installation"
Transaxle assembly
Differential side oil seal (left side)
Differential side oil seal (right side)
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA3729GB
JPDIA0118ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-691
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Remove differential side oil seal
using an oil seal remover (A)
(commercial service tool).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse differential side oil seal.
• Apply CVT fluid to differential side oil seals.
• When inserting the drive shaft, be sure to use Tool.
Install each differential side oil seal evenly using suitable tool so that
differential side oil seal protrudes by the dimension (C) and (D)
respectfully.
NOTE:
The reference is the installation direction of the differential side oil seal.
Drift to be used:
Inspection and Adjustment
INFOID:0000000010622903
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
JPDIA0118ZZ
Tool number
: KV38107900
: Differential side oil seal (LH)
: Differential side oil seal (RH)
JPDIA0520ZZ
Dimension (C)
:Height difference from case end surface is within 1.8
±
0.5 mm (0.071
±
0.020 in).
Dimension (D)
:Height difference from case end surface is within 2.2
±
0.5 mm (0.087
±
0.020 in).
Location
Commercial Service Tools
Transaxle case side
Commercial service tool with outer dia. 56 mm (2.20 in) and in-
ner dia. 50 mm (1.97 in)
Converter housing side
TM-692
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
WATER HOSE
WATER HOSE
Exploded View
INFOID:0000000010622904
Removal and Installation
INFOID:0000000010622905
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove the battery tray. Refer to
PG-143, "R9M : Removal and Installation"
.
2.
Remove the engine undercover. Refer to
EXT-40, "ENGINE UNDER COVER : Removal and Installation"
3.
Release hose clamps and remove water hose A and B.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse hose clamps.
• Securely install the water hose clip to the converter housing.
• Refer to the following when installing water hoses.
Hose clamp
Water hose A
Radiator hose assembly
Water hose B
CVT oil warmer
Transaxle assembly
: Always replace after every disassembly.
JSDIA5221ZZ
Hose
Installation side tube
Direction of paint mark
Hose insertion depth (L)
Water hose A
Radiator hose assembly
Frontward
: Hose end reaches the end
of radiator hose assembly tube.
CVT oil warmer
Frontward
: End reaches the 2-stage
bulge.
WATER HOSE
TM-693
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000010622906
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of engine coolant.
Water hose B
Radiator hose assembly
Frontward
: Hose end reaches the end
of radiator hose assembly tube.
CVT oil warmer
Upward
: End reaches the 2-stage
bulge.
Hose
Installation side tube
Direction of paint mark
Hose insertion depth (L)
ALDIA0475ZZ
Hose
Installation side tube
Hose clamp
Direction of tab
Clamping position (A)
Water hose A
Radiator hose as-
sembly
Rearward
5 – 7 mm (0.20 – 0.28
in) from hose end
CVT oil warmer
Frontward
Water hose B
Radiator hose as-
sembly
Rearward
CVT oil warmer
Leftward
JSDIA2424ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст