Nissan X-Trail 32. Manual — part 644
FRONT DOOR LOCK
DLK-917
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010728667
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
3.
Remove inside handle. Refer to
DLK-916, "INSIDE HANDLE : Removal and Installation"
.
4.
Remove sealing screen and front door glass run lower sash. Refer to
RUN LOWER SASH : Removal and Installation"
.
5.
Disengage outside handle cable
from cable clip
.
6.
Disengage rod holder
and disconnect key rod
from door lock assembly
according to the numerical
order 1
→
2 indicated by arrows as shown in the figure (driver side).
: Vehicle front
: Vehicle front
JMKIB3522ZZ
JMKIB3523ZZ
DLK-918
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR LOCK
7.
Remove door side grommet
, and then loosen TORX bolt
from grommet hole.
8.
Remove outside handle escutcheon
while pulling outside
handle grip
according to the numerical order 1
→
2 indicated
by arrows as shown in the figure.
9.
Slide outside handle grip
toward rear of vehicle and remove it
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
10. Remove front gasket
and rear gasket
.
JMKIB3524ZZ
JMKIA8374ZZ
JMKIA0524ZZ
: Pawl
: Vehicle front
JMKIB1627ZZ
FRONT DOOR LOCK
DLK-919
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
11. Slide outside handle bracket toward rear of vehicle and remove
it.
12. Disconnect outside handle cable
from outside handle bracket
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• When installing key rod, rotate key rod holder until a click is felt.
• After installation, check door lock. Refer to
DLK-916, "DOOR LOCK : Inspection"
.
: Vehicle front
JMKIB2034ZZ
JMKIB3525ZZ
DLK-920
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000010728714
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728715
REMOVAL
1.
Disconnect lock knob cable and inside handle cable from inside handle. Refer to
DLE : Removal and Installation"
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly connector.
4.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
Outside handle escutcheon
Rear gasket
TORX bolt
Door lock assembly
Inside handle
Outside handle bracket
Front gasket
Outside handle grip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3526GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст